How Do I Reset My Parrot Mki9200 Without Remote __full__ Review

Resetting a Parrot MKi9200 without the original wireless remote is typically not possible through standard menus, as the remote is the primary way to navigate settings. However, you can use these alternative methods depending on your vehicle's setup: JustCarKits 1. Steering Wheel Controls (UNIKA Interface) If your car has a Parrot UNIKA

interface installed, you can navigate the menu using your factory steering wheel buttons. JustCarKits Access the Menu : Press the following sequence on your steering wheel: Track Forward > Track Back > Track Forward > Track Back Navigate to Settings Track Forward button to scroll to "Settings". Perform Factory Reset Phone/Accept button to enter "Settings". Advanced Settings and select it. Factory Reset and confirm with the The unit will reboot and clear all paired devices. JustCarKits 2. Hard Reset via Power Cycle

While this won't always delete paired phones, it can clear temporary glitches or a "frozen" screen. JustAnswer Disconnect Power

: Remove the car battery terminal or disconnect the Parrot control box (usually hidden behind the dashboard) for at least 10 minutes to allow the capacitors to discharge. Check Wiring

: If the unit "forgets" settings every time you turn the car off, the red (permanent 12V) and orange (ignition) wires may need to be swapped. JustAnswer 3. Firmware Update how do i reset my parrot mki9200 without remote

Updating the firmware via a USB drive can sometimes force a memory wipe. JustCarKits Prepare a USB stick with the latest firmware from the official Parrot support site

Plug it into the MKi9200's USB cable. If the unit detects the update, it may overwrite existing data and reset the device. JustCarKits 4. Clearing "Memory Full" Errors If you are trying to reset because of a "Memory Full" message but cannot access the menu:

How to reset a Parrot MKi9200 without the remote - JustCarKits

Review: Resetting the Parrot MKi9200 Without the Remote Rating: ★★☆☆☆ Resetting a Parrot MKi9200 without the original wireless

I recently bought a used car that had a Parrot MKi9200 already installed. The system worked fine, but the previous owner didn't leave the wireless remote control, and the Bluetooth was paired to their old phones, meaning I couldn't connect mine.

I spent hours online trying to figure out how to do a "hard reset" or factory reset using just the screen and the steering wheel controls. Here is the conclusion I came to:

The Bad News: It seems impossible to fully factory reset the MKi9200 without the remote. The "Settings" menu—where the "Restore Factory Settings" option lives—is navigable, but the specific reset function is often blocked or requires a specific key combination that only exists on the remote.

I tried holding down the jog wheel, combinations of the red and green buttons on the screen, and disconnecting the battery for an hour. None of it cleared the paired devices list. Review: Resetting the Parrot MKi9200 Without the Remote

The Workaround (How I fixed it): Since I couldn't reset the memory, I had to use the "Delete All Pairs" method, but you need a phone already connected to do it. Since I couldn't connect my phone, I was stuck.

Eventually, I bought a cheap generic replacement remote on an auction site for about $15. The moment I put batteries in that remote, I was able to hold the red and green buttons down simultaneously to trigger the hardware reset.

Verdict: If you don't have the remote, you are essentially locked out of the system's administration functions. If you are in this situation, don't waste time trying button combos on the screen; just buy a replacement remote or check if your local car audio shop has a spare they can lend you for 30 seconds to wipe the memory.

Preventative Tips for the Future

Once you successfully reset your MKi9200 without the remote, take these steps to avoid the headache again:

1. Buy a spare remote – They are cheap and plug into the wired controller’s port.
2. Write down your pairing PIN (usually 0000 or 1234) and tape it to the glovebox.
3. Keep a paperclip in your car for hardware resets.
4. Learn the wired controller menu – It can do 90% of what the rotary remote does, including factory reset.

Step-by-step:

1. Locate the main "brain" box (usually hidden behind your dashboard, under a seat, or in the glovebox). It is a black plastic box about the size of a deck of cards with "Parrot" written on it.
2. Follow the wiring from the back of the LCD screen. It leads to this box.
3. Find the power connector (a black multi-pin block). Unplug it.
   • Alternative: If you cannot reach the box, simply disconnect your car battery for 30 seconds (warning: this may reset your car's radio presets and clock).
4. Wait 30 seconds.
5. Reconnect the power (or reconnect the battery).
6. Result: The Parrot will reboot completely. This fixes 95% of freezing or "no sound" issues but does not erase paired phones or settings.

Method 1: Use the Wired Control Pad (The Best Alternative)

The MKi9200 comes with a small, wired, button-style controller (often mounted near the gear stick). This is your lifeline when the rotary remote is missing.