The Tecom TS1162 is a 3-LED Remote Arming Station (RAS) keypad designed for use with Challenger security systems. It features a robust IP67-rated housing, making it suitable for both indoor and outdoor installation in dusty or wet environments. Installation Guide for Tecom TS1162 1. Preparation and Safety
Power Off: Ensure all power is disconnected from the Challenger panel or Intelligent Access Controller before starting any wiring to prevent damage.
Unpack: Verify the device for any physical damage and ensure all mounting hardware is present.
Location Selection: Choose a flat, vertical surface for mounting to prevent the base from flexing when tightened. 2. Mounting the Base
Disassemble: Remove the two retaining screws from the bottom of the keypad body and pull the bottom away from the base to disengage the top tabs.
Template: Use the base as a template to mark screw holes and the rear cable entry point (if using rear entry).
Secure: Use appropriate screws or bolts to mount the base to the surface. Ensure the tamper lever will be properly depressed against the surface when mounted to avoid constant tamper alarms. 3. Addressing and Configuration
Before completing the installation, you must set the device's unique address and termination on the internal DIP switches:
Device Address: Use DIP switches 1 through 4 to set the RAS address required for the Challenger system.
LAN Termination: If this keypad is the last device on the RS-485 LAN run, set DIP switch 8 to the "On" position to terminate the line. 4. Wiring and Termination
LAN Connection: Connect the keypad to the Challenger RS-485 LAN (up to 1.5 km away) using standard security cabling.
Request to Exit (RTE): Use the dedicated input for RTE control if required for the door.
Door Control: The open collector output can be used to drive a door relay or door strike.
Cable Routing: Avoid wire loops inside the enclosure and ensure cables do not lie directly on the circuit board. 5. Final Assembly
Hook Body: Place the top of the keypad body onto the mounting tabs of the base.
Secure: Swing the bottom into place and replace the two retaining screws at the bottom to lock the assembly. Maintenance Tips
Cleaning: Use a soft, dry cloth. For stubborn marks, use a small amount of isopropyl alcohol. Avoid water, ketones, or aromatic solvents.
Protection: Do not use sharp objects on the keypad surface; use fingers or gloved hands only.
For further technical documentation, you can visit the Aritech Support Portal for official Tecom manuals. TS1020 Analogue Data Gathering Panel Installation Manual
The Aritech (Tecom) TS1162 3 LED Remote Arming Station (RAS) Keypad
is a specialized security component designed for the Challenger series. Its installation manual is a critical resource for professional security installers working with robust, outdoor-rated access control systems. Manual Performance Review Technical Clarity: 9/10
The manual excels in providing exact wiring specifications for the RS-485 LAN connection, which allows the keypad to be located up to 1.5 km from the main Challenger panel. It clearly outlines the "Request to Exit" (RTE) input and the open collector output for controlling door strikes, ensuring installers can set up entry/exit points with precision. Practical Guidance: 8/10
For real-world application, the manual highlights the IP67 rating, confirming the device's suitability for wet or dusty environments. Step-by-step instructions typically include:
Addressing: Using DIP switches 1 through 4 to set the unique LAN address (1–16).
Tamper Protection: Specific notes on sealing the tamper switch to prevent false alarms.
Cabling: Guidance on terminating the RS-485 data cable shield to avoid electrical noise. Accessibility: 6/10
The TS1162 manual is primarily geared toward trained professionals. Much of the documentation is restricted to authorized installers through portals like Aritech Support, which can be a hurdle for end-users or DIY enthusiasts.
💡 Key Point: The manual’s emphasis on DIP switch configuration is vital; failing to set the 7th segment to "OFF" can trap the device in factory test mode, rendering it non-functional.
AI responses may include mistakes. For financial advice, consult a professional. Learn more Remote Arming Station (RAS) Keypad, 3 LED - Aritech ts1162 installation manual
The Tecom TS1162 is a 3-LED Remote Arming Station (RAS) designed for use with Challenger security systems. Rated at IP67, this robust keypad is suitable for both indoor and outdoor installations, including harsh, dusty, or wet environments.
This guide outlines the physical installation, wiring, and addressing procedures for the TS1162. 1. Preparation and Mounting
The TS1162 is designed for surface mounting. Its durable plastic housing allows it to be placed up to 1.5 km away from a Challenger panel or Intelligent Access Controller via the RS-485 LAN.
Location Selection: Choose a flat, solid, vertical surface to prevent the base from warping when tightened.
Tamper Protection: Ensure the mounting surface allows the rear tamper lever to be fully depressed when the unit is secured. Enclosure Removal: Undo the retaining screws at the bottom of the keypad.
Pull the bottom of the body away from the base and lift it off the top tabs.
Fixing: Use the base as a template to mark screw holes. Use appropriate fasteners for the mounting surface (e.g., wall plugs for masonry). 2. Wiring and Terminals
All power should be disconnected from the Challenger panel before wiring the RAS. The TS1162 typically features a pre-wired tail or screw terminals for the following connections: Connection Description LAN + / –
12V DC power from the Challenger LAN or an external power supply. D+ / D–
RS-485 data lines for communication with the Challenger panel. RTE Input Request to Exit (RTE) input for controlling door egress. OUT (Open Collector) A 50mA output used to drive a door relay or door strike.
Note: If the device is more than 100 meters from the main panel, it is recommended to use an external 12V power supply while maintaining a common negative (–) reference with the LAN. 3. Configuration (Addressing & Termination)
The Challenger system identifies each keypad by its unique RAS address, which must be set manually before the unit is powered up.
DIP Switches: Use the internal DIP switches (usually 1–4) to set the RAS address (1 through 16). Refer to your specific Challenger panel manual for the binary address table.
LAN Termination: If the TS1162 is the last device on a long RS-485 cable run, set the termination DIP switch (typically Switch 8) to the 'ON' position to prevent data signal reflections. 4. System Integration
Once physically installed and addressed, the keypad must be enabled within the Challenger system programming: Access the Installer Menu (Default code: 4346). Navigate to the RAS Configuration menu. Enable the specific RAS address you assigned to the TS1162.
Test the keypad by entering a valid user code to arm/disarm the assigned areas.
Maintenance Tip: For environments where the keypad face may become worn, a replacement TS1162-LABEL (membrane) is available to restore the unit's appearance and button legibility.
For further technical support or to download the full PDF documentation, visit the Aritech Support Portal or Ness Corporation.
Once you share the manual content or source, I can give you a clear, actionable review.
The identifier typically refers to the Santa Fe Advance100 Dehumidifier (document part number TS-1162) or the Tecom 3 LED Remote Arming Station (RAS) www.santa-fe-products.com 1. Santa Fe Advance100 Dehumidifier (TS-1162) TS-1162 Installation & Operation Instructions
cover the setup for this high-efficiency dehumidifier designed for crawl spaces and basements. www.santa-fe-products.com Key Installation Sections: Dehumidifier Setup:
Guidelines for placing the unit in a horizontal configuration.
Instructions for optional ducting to finished areas to manage airflow. Drain Installation:
How to set up the gravity drain or optional condensate pump. Electrical Requirements:
Specific power needs for the digital control and Wi-Fi compatibility. Maintenance: Changing air filters and basic servicing. resource.gemaire.com 2. Tecom TS1162 3-LED Keypad Tecom TS1162
is a robust remote arming station for Challenger security systems. aritech.com.au Installation Highlights: Connectivity:
Connects to the Challenger RS-485 LAN; can be located up to 1.5 km from the main panel.
Includes an input for Request to Exit (RTE) control and an open collector output for controlling door relays or strikes. The Tecom TS1162 is a 3-LED Remote Arming
Rated IP67, making it suitable for indoor or outdoor mounting in wet or dusty environments. Programming: Usually requires access through the ChallengerPlus Programming Manual to configure RAS beepers or area arming. aritech.com.au Are you installing the Santa Fe dehumidifier or setting up the Tecom security keypad Installation & Operation Instructions - Gemaire
Tecom TS1162 is a 3-LED Remote Arming Station (RAS) keypad used with the Challenger
security system. It is specifically designed for harsh or wet environments, featuring a robust construction and an IP67 rating Ness Corporation General Installation Steps
While technical manuals for Tecom hardware are often restricted to trained installers on the Aritech portal
, the general installation procedure for Challenger RAS devices includes: support.firesecurityproducts.com.au Preparation
: Power down the Challenger panel before beginning any wiring.
Unscrew the retaining screws and remove the body assembly from the base.
Use the mounting template to mark screw holes and cable entry on the surface. Ensure the tamper lever will be depressed when the unit is mounted. Connect the device directly to the Challenger RS-485 LAN Data/Power
: Use the standard Challenger LAN terminals (+, –, D+, D-). For runs over 100 meters, a separate 12V power supply is recommended. Inputs/Outputs : The TS1162 includes a Request to Exit (RTE) input and one open collector output for controlling door relays or strikes. Addressing & Configuration RAS address using the internal DIP switches (typically switches 1–4).
Set LAN termination (DIP switch 8) if the device is at the end of a LAN run. Final Assembly
: Hook the top of the body onto the base and secure it with the retaining screws. Ness Corporation Key Features Connectivity : Can be placed up to from the Challenger panel or Intelligent Access Controller. Protection , making it suitable for dusty or outdoor applications.
: Features 3 LED status indicators rather than a full LCD screen. aritech.com.au
For full configuration and programming, you may need to access the ChallengerPlus Installation and Programming Manual or contact Aritech Technical Support for restricted documents. support.firesecurityproducts.com.au or details on how to program the door output for this keypad? Remote Arming Station (RAS) Keypad, 3 LED - Aritech
Remote Arming Station (RAS) Keypad, 3 LED * Robust moulded plastic housing. * Indoor or outdoor mounting. * Request to Exit input. aritech.com.au Tecom TS1162 3 LED RAS - Ness Corporation
Tecom TS1162 is a robust, 3-LED Remote Arming Station (RAS) keypad designed for use with Tecom Challenger
security systems. It features an IP67 rating, making it suitable for wet or dusty environments, and supports a maximum LAN distance of 1.5 km. aritech.com.au Draft Installation Guide: Tecom TS1162 1. Pre-Installation Requirements
: Use 2-pair twisted shielded data cable (e.g., Belden 8723) for the RS-485 LAN connection.
: Ensure all power is turned off to the Challenger control panel before beginning any wiring. Environment
: Select a mounting location suitable for the device’s IP67 rating if installing outdoors. aritech.com.au 2. Mounting the Device Disassembly
: Remove the body retaining screws from the bottom of the unit and pull the body away from the base.
: Use the provided mounting template to mark screw holes. Ensure the tamper lever
will be fully depressed once the base is mounted to the surface.
: Secure the base assembly to the wall using suitable screws for the surface type. aritech.com.au 3. Addressing and Configuration Address Selection
: Use DIP switches 1 through 4 to set the unique RAS address. LAN Termination
: If the TS1162 is the last device on the LAN run, set DIP switch 8 to the "ON" position for proper termination. aritech.com.au 4. Wiring and Connectivity Challenger LAN : Connect to the RS-485 LAN terminals (D+, D-, +12V, 0V). Inputs/Outputs Request to Exit (RTE)
: Connect a standard push-button or sensor to the designated input for door release. Door Control
: Utilize the open collector output to trigger a door relay or strike.
: Join data cable shields where the cable extends past the device. Connect the shield to the LAN earth terminal at the panel end. aritech.com.au 5. Final Assembly Reattach Body The full name of the product (e
: Hook the top of the keypad body onto the base tabs and swing the bottom into place. : Replace and tighten the body retaining screws.
: Power up the system and verify communication with the Challenger panel. aritech.com.au or specific DIP switch settings for a particular address? Remote Arming Station (RAS) Keypad, 3 LED - Aritech
Remote Arming Station (RAS) Keypad, 3 LED * Robust moulded plastic housing. * Indoor or outdoor mounting. * Request to Exit input. aritech.com.au Tecom TS1162 3 LED RAS - Ness Corporation
The Tecom TS1162 is a 3 LED Remote Arming Station (RAS) keypad designed for the Challenger security system. It is frequently used in environments requiring robust construction, such as dusty or wet locations, due to its IP67 rating. 1. Key Specifications
Connectivity: Connects directly to the Challenger RS-485 LAN.
Operating Range: Can be installed up to 1.5 km from the main Challenger panel or Intelligent Access Controller. Inputs/Outputs: One input for Request to Exit (RTE) control.
One open collector output for controlling door relays or strikes.
Durability: Robust molded plastic housing suitable for indoor or outdoor mounting. 2. General Installation Steps While specific detailed
manuals are often restricted to authorized installers, the procedure follows standard Tecom RAS installation protocols as seen in similar models like the TS1001:
Preparation: Power down the Challenger panel before beginning any wiring.
Disassembly: Remove body retaining screws and separate the body from the base. Mounting:
Use the provided template to mark mounting holes and cable entry points.
Ensure the tamper lever will be fully depressed once mounted to avoid false tamper alarms.
Secure the base to the wall using appropriate screws for the surface type.
Addressing: Use the internal DIP switches (typically switches 1–4) to set the unique RAS address on the LAN.
Termination: If this is the last device on the RS-485 LAN, set the LAN termination DIP switch (usually switch 8) to ON. Wiring: Terminate the LAN cabling (+, –, D+, D–). Connect the RTE input and door relay output if required.
Reassembly: Hook the top of the body onto the base tabs and secure with the bottom retaining screws. 3. Support and Documentation
For the full technical manual, installers can access the Aritech/Tecom Support Portal.
Manuals Library: Official documents are hosted on the Aritech Support Site.
Authorized Access: Note that some detailed installation and programming manuals are restricted to trained installers with valid login credentials. Tecom Manuals - Kidde Global Solutions Support
You're looking for the installation manual for the TS1162!
The TS1162 is a specific model, and I'd be happy to help you find the manual. Here are a few options:
If none of these options work, please provide more context or details about the product (e.g., what type of device is it, and where you encountered it). I'll do my best to help you find the installation manual!
The TS1162 installation manual recommends routine checks every 6 months in normal environments, or monthly in dusty/humid conditions.
After wiring, perform Dry Run:
Pass criteria: All sensors report stable values; no relay chattering; no error codes.
For cable-free printing, the TS1162 installation manual recommends using the WPS (Push Button) method.
Perform outdoors on a clear day (fresh air ≈ 420 ppm).
The manual includes standard safety warnings regarding the airbag (located in the A-pillar) and the handling of glass. These are prominent and necessary, earning the manual points for safety consciousness.