Skip to content

Smartpack2 Touch User Manual «100% LIMITED»

The Eltek Smartpack2 Touch is a high-resolution master controller designed for local monitoring and management of DC power systems. It features a touch screen for interface navigation, Ethernet and USB connectivity, and supports remote monitoring via SNMP or Web browser. For comprehensive technical details, download the User's Guide - Smartpack2 Touch Controller. Modular HE with Smartpack2 Touch - Kitsap 911

SmartPack2 Touch User Manual: A Comprehensive Guide The SmartPack2 Touch is the next generation of power system controllers, offering a highly intuitive touchscreen interface to manage complex DC power plants. Whether you are overseeing a telecommunications site or an industrial power hub, this manual provides the essential steps to get your system up and running. 1. Hardware Overview

The SmartPack2 Touch features a 4.3-inch high-resolution color display. Unlike its predecessors, which relied heavily on navigation buttons, the "Touch" model allows for direct interaction with icons and menus. Key Components:

Touchscreen: The primary interface for monitoring and configuration.

USB Port: Located on the front for firmware updates and configuration uploads/downloads. Status LEDs: Green (Power): System is operational. Yellow (Warning): Non-critical alarm present. Red (Alarm): Critical system fault. 2. Navigating the Interface

The home screen provides a high-level "Dashboard" view of your system's health.

System Status: Shows total load, battery voltage, and current.

Menu Icon: Tap the three horizontal lines (hamburger menu) to access deep settings. Back Button: Returns you to the previous screen. Home Button: Instantly returns you to the main dashboard. 3. Initial Configuration smartpack2 touch user manual

When you first power on the SmartPack2 Touch, you will need to perform a basic setup to ensure accurate monitoring. Setting the Language and Time Navigate to Settings > General > Language.

Set the Date and Time under the same menu to ensure log timestamps are accurate. Battery Setup This is the most critical step for system longevity. Go to Settings > Battery. Select the Battery Type (e.g., Lead Acid, Li-Ion, NiCd). Input the Battery Capacity (Ah) and the number of strings.

Configure the Charge Current Limit to prevent overheating during recharge cycles. 4. Alarm Management

The SmartPack2 Touch allows for granular control over what triggers a notification.

Thresholds: You can set "High Voltage" and "Low Voltage" disconnect points under Settings > Alarms.

Relay Mapping: Assign specific alarms (like "Mains Failure") to physical output relays on the controller’s backplane.

Viewing Logs: Tap the Alarm Log icon on the home screen to see a chronological history of system events. 5. Connectivity and Remote Access The Eltek Smartpack2 Touch is a high-resolution master

The controller is designed to be managed from anywhere via an Ethernet connection.

IP Configuration: Go to Settings > Communication > Ethernet. You can choose DHCP or assign a Static IP.

Web Interface: Once the IP is set, type it into any web browser on your network to access the full management suite remotely.

SNMP: For centralized monitoring, enable SNMP (v1, v2c, or v3) to integrate with your Network Management System (NMS). 6. Maintenance and Troubleshooting Firmware Updates

To keep your system secure and efficient, update the firmware periodically:

Download the latest firmware from the manufacturer’s portal. Save it to a FAT32-formatted USB drive.

Insert the drive into the SmartPack2 Touch and select Maintenance > Update Firmware. Resetting the Controller Long-press the Gear Icon

If the screen becomes unresponsive, you can perform a "Soft Reset" by holding the pinhole reset button for 5 seconds. This will restart the controller without interrupting the DC power to your loads. Summary Table: Quick Commands Navigation Path Check Load Home Dashboard Change Voltage Settings > Power System > Voltage Control Export Logs Maintenance > USB > Export Logs Test Relays Maintenance > Diagnostics > Relay Test

Disclaimer: Always refer to the specific wiring diagrams provided with your power plant rack, as physical configurations may vary by installation.

4.3 Setting Temperatures

  1. Long-press the Gear Icon.
  2. Tap the numeric field for Top Seal Temp.
  3. Use the pop-up digital keypad to enter target temperature (e.g., 135°C).
  4. Slide the Dwell Time slider to adjust jaw closing duration.

Step 3: AC Input

7. Troubleshooting – Common Alarms

| Alarm Message | Probable Cause | Operator Action | |---------------|----------------|------------------| | Film Break | Roll empty or torn | Load new film; rethread path | | Temp Low | Heater failed or thermocouple open | Check heater SSR; call maintenance | | Encoder Fault | Dirty or disconnected encoder | Clean connector; cycle power | | Air Pressure Low | < 5 bar (if pneumatic) | Check shop air supply | | Jaw Overtemp | >220°C | Stop machine; cool 10 min; check PID tuning |

2. What’s in the Box

3. Anatomy of the SmartPack2 Touch

External:

Internal:

4. Navigating the Interface

The main screen is usually divided into three sections: Header, Main Display, and Footer.

6. Daily Startup Sequence

  1. Pre-start inspection: Clean sealing surfaces, verify film roll tracking.
  2. Power ON: HMI shows System Ready (green).
  3. Warm-up: Set temperature → wait until Temp Stabilized (approx. 3–5 min).
  4. Load recipe or manually enter parameters.
  5. Manual test: Feed one bag length → inspect seal integrity.
  6. Switch to Auto → press Start.
Free Link
DVD & Additional Screening Options