Our Core Purpose Our heritage Our Books How to Get Published Contact Us Hiyas Job Opportunities New Page
All Bookshops Loyalty Programs

Sinotimer Tm-630s Manual ~repack~

Introduction

The Sinotimer TM-630S is a digital timer controller designed for various industrial and commercial applications. This manual provides a detailed guide on the installation, operation, and maintenance of the TM-630S timer.

Overview of the TM-630S

The TM-630S is a microprocessor-based timer that offers a wide range of features, including:

  • 6-digit LED display
  • 16 timing ranges (0.01s to 9999.9h)
  • 4 control modes (A, B, C, and D)
  • 2 relay outputs
  • 1 analog output (optional)
  • Communication interface (RS485 or MODBUS)

Installation

  1. Unpacking and Inspection: Carefully unpack the TM-630S and inspect for any damage or defects.
  2. Mounting: Mount the TM-630S on a standard 35mm DIN rail or on a flat surface using the provided screws.
  3. Wiring: Connect the power supply, input signals, and output relays according to the wiring diagram provided in the manual.

Operating Instructions

  1. Power On/Off: Press the [POWER] button to turn the TM-630S on or off.
  2. Setting the Time: Use the [▲] and [▼] buttons to set the desired time. The time can be set in seconds, minutes, hours, or days.
  3. Selecting the Control Mode: Choose one of the four control modes (A, B, C, or D) using the [MODE] button.
  4. Setting the Relay Outputs: Configure the relay outputs according to the desired application.

Control Modes

The TM-630S offers four control modes:

  1. Mode A (Interval Mode): The relay output is activated for a set time interval.
  2. Mode B (Delay Mode): The relay output is activated after a set delay time.
  3. Mode C (Cycle Mode): The relay output is activated for a set time interval and then deactivated for another set time interval.
  4. Mode D (Loop Mode): The relay output is activated for a set time interval and then deactivated for another set time interval, repeating the cycle.

Analog Output (Optional)

The TM-630S can be equipped with an analog output (0-10V or 4-20mA) for monitoring the timer's status. sinotimer tm-630s manual

Communication Interface

The TM-630S can be connected to a computer or a control system using the RS485 or MODBUS communication interface.

Maintenance and Troubleshooting

  1. Cleaning: Regularly clean the TM-630S to prevent dust and debris accumulation.
  2. Error Messages: Consult the manual for error messages and troubleshooting procedures.
  3. Replacement of Fuses: Replace fuses according to the manual's instructions.

Technical Specifications

  • Power Supply: 85-265VAC, 50/60Hz
  • Consumption: <5W
  • Input Signals: 2 inputs (start, reset)
  • Output Relays: 2 relay outputs (SPST)
  • Analog Output: 0-10V or 4-20mA (optional)
  • Communication Interface: RS485 or MODBUS
  • Operating Temperature: -10°C to 50°C
  • Storage Temperature: -20°C to 70°C

Conclusion

The Sinotimer TM-630S is a versatile and reliable timer controller suitable for various industrial and commercial applications. This manual provides comprehensive information on the installation, operation, and maintenance of the TM-630S, ensuring optimal performance and longevity.

Sinotimer TM-630S is a versatile, 7-day digital programmable timer switch capable of handling high-power loads up to 30A. Unlike basic models, the "S" series features a 1-second minimum interval

, making it ideal for precise industrial or household applications. Key Technical Specifications Power Supply Options: 200–250VAC (50/60Hz) or 12VDC models available. Load Capacity: 30A (Resistive). Timing Range: 1 second to 168 hours. Up to 28 ON/OFF daily/weekly settings. Memory Backup:

Built-in rechargeable battery keeps settings for up to 90 days during power outages. Panel or wall-mounted. Setup & Programming Guide 1. Unlock the Device The screen often auto-locks to prevent accidental changes. Introduction The Sinotimer TM-630S is a digital timer

to unlock the panel. A small "a" or lock icon will disappear from the display. 2. Setting the Current Time button while pressing the following: To set the current day of the week. To set the current hour. To set the current minute. To set the current second. 3. Setting ON/OFF Programs button. The screen will show "1 ON".

to select which days the program should run (e.g., all week, weekdays only, or specific days). to set the exact time you want the device to turn ON. again to show "1 OFF".

Repeat the same steps (Days, Hours, Minutes, Seconds) to set the OFF time. to save and exit. 4. Operating Modes button to cycle through: Permanently ON. Permanently OFF. Executes your saved programs. Wiring Overview Pins 1 & 2: Power supply input. Pins 3 & 4: Load output (switch side). For further details, you can consult the official Sinotimer Support or download a digital copy via for your power source (12V vs 220V)? sinotimer-tm-630a-operating-manual.pdf - pic-control

The SINOTIMER TM-630S is a professional-grade, 7-day digital programmable timer switch designed for industrial and domestic automation. Unlike standard timers, the TM-630S supports 1-second interval precision, making it ideal for tasks requiring short, high-frequency bursts of power, such as school bells, factory sirens, or complex irrigation systems. Key Technical Specifications

The TM-630S is available in several voltage variants (e.g., 110V, 220V, or 12V DC) to suit different power requirements.

Load Capacity: Supports high loads up to 30 Amps (approximately 5000 Watts). Programming: Up to 28 ON/OFF daily or weekly programs. Minimum Interval: 1 second.

Power Reserve: Integrated 3V rechargeable battery retains programs for up to 60–90 days during power outages. Installation: Designed for panel or wall mounting. Initial Setup: Unlocking and Time Sync

Before programming, the device often locks itself to prevent accidental changes.

Finding the exact manual for the Sinotimer TM-630S can be difficult because it is a generic Chinese-manufactured device often sold under various brand names. However, the TM-630S is a standard Time Switch (Programmable Timer) used to control electrical appliances (lights, water heaters, fans, etc.) based on a set schedule. 6-digit LED display 16 timing ranges (0

Below is a comprehensive operation guide based on the standard functionality of the TM-630S module.

List of Typical Modes (17 Functions)

The "mode" refers to how the timer applies the ON/OFF times. You select the mode by pressing PROG and holding the up/down arrows until you see a specific symbol.

Here is the key interpretation:

| Mode | Display Symbol | Meaning | Typical Use | | :--- | :--- | :--- | :--- | | Mode 1 | Single block | Timer cycles once at set time | Delayed start | | Mode 2 | Recurring arrow | Continuous cycles (ON for X min, OFF for Y min) | Hydroponic pumps | | Mode 3 | 24H + cycle | 24-hour cycle with specific ON/OFF times | Street lights | | Mode 4-17 | Weekday sequences | Different programs for different days | Office lights (M-F, Sa-Su separate) |

The most common mode for beginners is Mode 3 – Simple 24-hour repeating timer with one ON time and one OFF time.

Example: Turn a light ON at 6:00 PM and OFF at 6:00 AM daily.

  1. Set mode to "24H" (Mode 3).
  2. Program 1ON for 18:00.
  3. Program 1OFF for 06:00 (next day – the timer automatically handles crossover).
  4. Set days to "All" (Mo Tu We Th Fr Sa Su).
  5. Exit programming. Ensure unit is in AUTO.

🔍 Where to Find the Official Manual

  1. Check the product listing – If you bought it on Amazon, eBay, or AliExpress, the seller often uploads a PDF manual in the “Product Guides” or “Documents” section.
  2. Sinotimer’s official website – Visit sinotimer.com and search for TM-630S under “Downloads” or “Support.”
  3. Third-party manual sites – Sites like ManualsLib or Manuals.plus sometimes host user-uploaded Sinotimer manuals.
  4. Contact Sinotimer directly – Their support email is often listed on their website.

Downloading the Official Sinotimer TM-630S Manual PDF

While this guide covers 99% of usage, you may want the original 2-page pamphlet. You can download the Sinotimer TM-630S manual in PDF format from:

  • The product listing on AliExpress or Amazon (often under “Technical Specification”)
  • ManualsLib.com (search “TM-630S”)
  • Sinotimer’s official website (sinotimer.com, though the site is largely industrial)

Step 2: Set the Time Base (Seconds, Minutes, Hours)

After selecting your mode, press SET once. You will see a blinking value like 1S. This is the time base:

  • S = Seconds
  • M = Minutes
  • H = Hours
  • S with a dot (or S.) = 0.1 Seconds (tenths of a second)

Press ∧ or ∨ to change the unit. Press SET to lock it.

Rear Panel & Wiring Terminals

  • Terminal 1 & 2: Power Input (Live/Neutral or DC +/-)
  • Terminal 3 & 4: Relay Output (COM & NO – Normally Open)
  • Terminal 4 & 5: Relay Output (COM & NC – Normally Closed)

Important: Always disconnect power before wiring. If you are not a qualified electrician, consult one. Incorrect wiring can destroy the unit or cause fire.