Nokia Ta1174 Flash File Mtk Top Extra Quality Direct

The Nokia TA-1174 (Nokia 105, 2019 edition) is a popular feature phone known for its durability, but software glitches—like being stuck on the logo, contact service errors, or security code locks—often require a fresh firmware installation.

Finding the correct flash file is critical because there are two distinct versions of this device: the original model (SPD chipset) and the clone model (MTK chipset). 🛠️ Important Hardware Distinction

Before downloading any files, you must identify your device's CPU. Flashing the wrong firmware can "brick" the phone permanently.

Original Nokia 105 (TA-1174): Uses the Spreadtrum (SPD) SC6531EFM chipset.

Clone/Copy TA-1174: Often uses MediaTek (MTK) MT6261 or MT6250 chipsets. 📂 Nokia TA-1174 Flash File & Tool Requirements

To perform a successful flash, you will need the following "top-tier" resources: Firmware (Flash File):

For MTK Clones: Look for the MT6261 TA-1174 Bin File which is compatible with most "China-made" versions of this model.

For Original SPD: Use the v40.00.17.03 Flash File, which is a tested and stable version. Flashing Tools:

MTK Versions: Use Miracle Box, Piranha Tool, or Infinity CM2MTK.

SPD Versions: Use Avenger Spreadtrum Module, NCK Box, or Infinity CM2SPD.

USB Drivers: Ensure the MTK USB VCOM Drivers or SPD Flash Drivers are installed on your PC. 📝 Step-by-Step Flashing Guide (MTK Version) nokia ta1174 flash file mtk top

Follow these steps to restore your MediaTek-based Nokia clone:

Preparation: Charge your phone to at least 50% and back up any data if the device still powers on.

Run the Tool: Open your preferred MTK flash tool (e.g., Miracle Box).

Select File: Go to the "Service" or "Write" tab and select the Nokia TA-1174 MTK Flash File (.bin).

Boot Key: The standard boot key for the Nokia 105 is usually the center "OK" button or the "Back/Menu" button.

Connect: Click "Start" in the tool, hold the boot key, and connect the phone to your PC via USB cable.

Flashing: The tool will recognize the device and start the "Writing" process. Do not disconnect until you see a "Write Complete" message. ⚠️ Troubleshooting Common Issues

Not Detected: Try a different USB cable or port. Reinstall drivers if the PC shows "Unknown Device."

Dead After Flash: This usually happens if you flash an MTK file onto an SPD device. You must re-flash with the correct SPD firmware to revive it.

IMEI Null: If the IMEI is lost after flashing, use the Write IMEI feature in Miracle Box to restore the original numbers from the sticker behind the battery. The Nokia TA-1174 (Nokia 105, 2019 edition) is

Nokia 105 (TA-1174) typically uses a Spreadtrum (SPD) chipset, specifically the . While some "clone" versions or regional variants may use MediaTek (MTK) chips like the

, you must first verify your device's hardware before flashing to avoid bricking. Flash File Details

Spreadtrum SC6531EFM (Standard) or MediaTek MT6261DA (Clone/Variant). Firmware Version: 40.00.17.03 is a commonly tested stable version. Common Fixes:

Resolves "Contact Service" errors, hang-on-logo issues, and forgotten security codes. Required Tools & Resources

The Nokia 105 (2019) Go to product viewer dialog for this item. , model Go to product viewer dialog for this item.

, is typically powered by a Spreadtrum (SPD) chipset, specifically the SC6531EFM. While some "clone" versions or specific variants may reference MTK (MediaTek) chipsets like the MT6261DA or MT6260, standard original units use SPD drivers and tools. Flash File & Tool Requirements To flash this device, you generally need:

Flash File: A tested firmware file (often .bin or .pac format) specifically for the

Drivers: SPD USB Drivers (for the SC6531 chipset) or MTK VCOM Drivers depending on the specific board version.

Flash Tool: Common tools include Avenger Box (Spreadtrum Module), Infinity BEST Dongle, or Nck Dongle. Flashing Procedure

Backup Data: Flashing will erase all personal data; ensure a backup is made if possible. Disconnect the USB cable

Install Drivers: Download and install the appropriate USB drivers on your PC.

Load Firmware: Open your chosen flash tool (e.g., Avenger Box ) and select the firmware file. Connect Device: Power off the phone.

Hold the Boot Key (often the 'Center' or 'Left Soft Key') while connecting the device to your PC via USB cable.

Start Flashing: Click the "Start" or "Write" button in the tool. The progress bar will begin once the device is detected.

Completion: Once the tool shows a "Success" or "Download Complete" message, unplug the device and power it on.

For a visual walkthrough of the flashing process using SPD tools, watch this guide:

Here is the text guide and information regarding the Nokia TA1174 Flash File (MTK).

Device: Nokia TA1174 Chipset: MediaTek (MTK) Processor: MT6761 or MT6765 (Helio A22/G25)

Step 7: Post-Flashing Steps

  1. Disconnect the USB cable.
  2. Perform a hard reset: Press and hold Power + Volume Up for 15 seconds.
  3. The phone should boot to the welcome screen. First boot may take up to 5 minutes.

6.3 FRP Removal (Google Account Lock)

If you flashed without wiping userdata and are stuck on "Verify your account":

Troubleshooting Common Errors in MTK Top Tool for Nokia TA1174

| Error | Cause | Fix | |-------|-------|-----| | S_BROM_CMD_STARTCMD_FAIL | Preloader handshake issue | Reinstall VCOM drivers; try a different USB port (USB 2.0). | | S_FT_DOWNLOAD_FAIL (4008) | Wrong scatter file | Verify you are using TA1174-specific files, not TA1143 or TA1194. | | BROM ERROR: S_SECURITY_AC_SEC | Authentication required | Use MTK Top’s “Bypass” feature under Tools > MTK Auth Bypass. | | DA_HASH_MISMATCH | Corrupted Download Agent | Extract the DA file from the firmware folder instead of default. | | Phone stays dead after flash | Battery disconnected internally | Open the phone, disconnect battery flex for 30 seconds, reconnect. |

1. Install MTK USB VCOM Drivers

Step 3: Launch MTK Top Tool

  1. Run MTK_Top_Tool.exe as Administrator.
  2. Select MediaTek tab.
  3. Under “Mode,” choose BootROM (BROM) – not Preloader.
  4. Click Scatter/Config and load your MT6261_Android_scatter.txt.

File Details:

Step 4: Prepare the Phone