Nokia 105 Ta-1174 Flash Tool |link| Download May 2026
Since you are looking for a review of the "Nokia 105 TA-1174 Flash Tool," it is important to clarify exactly what these tools are, as there isn't one single official "Nokia 105 Tool" distributed to the public.
Based on the device model (TA-1174), you likely have the 2019 edition of the Nokia 105. This phone runs on a simple RTOS (Real-Time Operating System), not Android.
Here is a comprehensive review of the tools available for this device, covering usability, safety, and functionality. nokia 105 ta-1174 flash tool download
2. Download SP Flash Tool
Do not use random “Nokia 105 flash tool” from unknown forums — many are fake or malware.
- Official source: MediaTek doesn’t release it publicly, but trusted mirror:
- Go to https://spflashtool.com
- Download latest Windows version (e.g., v5.2216 or newer)
- Alternative: MTK Client (newer, open-source) – good for backup/restore without full flash.
Troubleshooting common issues
- Flash tool fails to detect device: reinstall drivers, try different USB port/cable, enable battery reinsert method, try another PC.
- Flash stalls or errors: cancel, disconnect, reboot PC and phone, try alternative tool or different firmware mirror.
- Missing IMEI or network issues after flash: restore NV/NvRam files if package includes them; reflash NV only if you have correct NV file for your region.
- Boot loop after flash: try full wipe/factory reset if allowed by tool; reflash again with same firmware.
6. Finish
- Once done, the tool will show “Done” or “Success”.
- Disconnect the phone, reinsert battery, and power it on.
Step 6: Completion
- Wait 3–5 minutes. When you see "Flash Completed Successfully" or "Done", click Stop.
- Disconnect the USB cable.
- Remove the battery for 10 seconds, reinsert it, and press the power button.
Congratulations! Your Nokia 105 TA-1174 should boot into a fresh, clean system. Since you are looking for a review of
Is It Worth Flashing a Nokia 105?
The Nokia 105 TA-1174 costs roughly $20–25. Sending it to a repair center for flashing could cost $30–50. That doesn't make sense. However, if you are a hobbyist, a repair shop owner, or someone who hates e-waste, using a flash tool download to revive the phone is both economical and satisfying.
Files and tools you’ll need
- Stock firmware (TA‑1174) — usually distributed as a small ZIP containing .pac/.img or MT6250/SC6531EFM‑based files, NV data, and scatter/loader where applicable.
- Flash tool(s):
- SP Flash Tool / Miracle Box variants — used for many MediaTek/feature‑phone chipsets (check file type).
- PhoenixTool / Infinity Box / UFS/Avatech flasher — used by some feature‑phone workflows.
- MTK/Spreadtrum specific tools if the package is SPD/SC653x or MTK‑based.
- USB drivers:
- MediaTek/Spreadtrum/USB VCOM drivers (depending on chipset).
- Windows PC (recommended) and a good USB cable.
Note: Many download pages label TA‑1174 firmware as “SC6531EFM” or “MT6250 clone” depending on the build—match the chipset reported by the device. Official source : MediaTek doesn’t release it publicly,
Common Errors & Fixes:
| Error | Solution |
|-------|----------|
| S_DL_GET_DRAM_SETTING_FAIL | Wrong firmware; redownload for TA-1174 only. |
| Port not found | Reinstall SPD drivers; try different USB port. |
| BROM error 0x6 | Battery too low; charge for 30 minutes. |
| Stuck at 0% | Use USB 2.0 port; disable driver signature enforcement. |
2. USB Drivers Required
Before flashing, install the Unisoc/Spreadtrum USB drivers:
- Driver: SPD Driver v2.0.0.4 or later
- Mode used: Download mode (phone off → hold Vol- → connect USB)
- Device appears in Device Manager as:
SPRD U2S Diag or Unisoc Phone
Download:
SPD USB Drivers for Windows 10/11
