The MS-7613 (ver 1.1), codenamed "Iona-GL8E" and manufactured by MSI for HP, is a micro-ATX motherboard supporting LGA 1156 socket Intel processors and the H57 Express chipset. Key features include four DDR3 DIMM slots for up to 16GB of RAM, one PCIe x16 slot, and onboard Realtek audio, generally designed for Windows 7-era, legacy systems. Detailed specifications and, and motherboard layout information can be found in the Scribd document

MS-7613 (Iona-GL8E) Motherboard Specifications | PDF - Scribd

The MS-7613 Ver 1.1 motherboard (often referred to by its HP/Compaq codename "Iona-GL8E") is a micro-ATX board originally manufactured by MSI for use in HP desktop systems like the HP Pavilion and Pavilion Elite series.  Core Specifications  Form Factor: Micro-ATX (24.4 cm x 24.4 cm). Socket: LGA 1156. Chipset: Intel H57 Express.

Power Connectors: One 24-pin ATX power connector and one 4-pin ATX (12v) power connector.  CPU & Memory Compatibility 

Supported Processors: Works with Intel Core i7-8xx, i5-7xx, i5-6xx, and i3-5xx series. Note that it generally supports a maximum processor core frequency of 2.93GHz or less. Memory (RAM): Type: DDR3 (240-pin) Non-ECC, unbuffered. Slots: 4 DIMM slots supporting dual-channel architecture. Speed: PC3-10600 (DDR3-1333) or PC3-8500 (DDR3-1066).

Capacity: Up to 16 GB (specifically using 4GB DIMM modules in each slot).  Expansion & Connectivity  Internal Slots: 1 x PCI Express x16 (for graphics). 3 x PCI Express x1.

1 x PCI Express x1 Mini-Card socket (often used for WLAN cards). 4 to 6 x SATA 2.0 (3.0 Gb/s) connectors. Back I/O Ports: 1 x VGA and 1 x DVI port. 6 x USB 2.0 ports. 1 x RJ-45 LAN (Gigabit). 6 x Audio ports (supports up to 8-channel audio).

1 x Optical S/PDIF output and 1 x IEEE 1394 (Firewire) port.  Maintenance Procedures 

Detailed technical diagrams and specifications can be found on resources like Scribd and The Retro Web. 

Clearing CMOS: Locate the JBAT1 jumper. Move the jumper to pins 2-3 for 5–10 seconds, then return it to pins 1-2 to reset BIOS settings.

Resetting BIOS Password: Use the JPD1 jumper to erase forgotten passwords by following the same pin-bridging procedure. 

Are you troubleshooting a specific issue, or are you looking to upgrade a component like the RAM or CPU?  Compatible RAM with HP p6307ru MS-7613 motherboard

The Hewlett-Packard MS-7613 (Iona-GL8E) Motherboard Guide

If you are reading this, you likely have an older Hewlett-Packard (HP) desktop computer—such as a Pavilion, Compaq Presario, or HP 300/500 series—and you are looking for specifications, upgrade options, or troubleshooting advice for the motherboard stamped MS-7613 VER: 1.1.

Because this board was an OEM product manufactured by MSI for HP, finding a traditional "manual" on MSI’s public website is often impossible. Below is a reconstruction of the critical technical manual details you need.

Part 7: Compatible Parts Guide (Manual-Based)

The manual’s Qualified Vendor List (QVL) is outdated, but based on its electrical specs, here is modern (used market) compatibility:

| Component | Best match (proven working) | | --- | --- | | CPU | Core 2 Quad Q9650 (1333 MHz FSB) – check cooling. | | RAM | 2 x 4 GB DDR3-1066 (Kingston KVR1066D3N7/4G) – 8 GB max. | | GPU | Any PCIe 2.0 or 1.0 card (e.g., Radeon HD 5450, GT 710) – no UEFI BIOS needed. | | SSD | SATA II SSD (Kingston A400) – works, but limited to 3 Gb/s. | | PSU | 250W–350W ATX (20+4 pin) – do NOT use modern high-wattage PSU without testing; the board has no +12V overcurrent protection. |

The manual explicitly says: “Do not install Pentium Extreme Edition 965 (130W TDP).” The VRM cannot handle it.

2. Processor Support (CPU)

The MS-7613 uses the LGA 1156 socket. It supports Intel processors with an integrated memory controller. Before upgrading, check your specific BIOS version, as HP BIOS updates often added support for newer CPU steppings.

Supported Architectures:

• Intel Core i7: 800 series (e.g., i7-870, i7-860).
• Intel Core i5: 600 and 700 series (e.g., i5-650, i5-660, i5-750).
• Intel Core i3: 500 series (e.g., i3-530, i3-540).
• Intel Pentium: G6000 series (Dual-core).

Note: This board does not support 2nd Gen (Sandy Bridge) or 3rd Gen (Ivy Bridge) i5/i7 processors. It is strictly 1st Generation.

4. Internal Connectors & Pinouts

If you are transplanting this board into a different case or repairing a front panel connection, the pinouts are critical.

5. Expansion Slots

This board was designed for mid-range usage and includes legacy slots for older cards.

1. PCIe x16: One full-length slot for a dedicated graphics card.
2. PCIe x1: Two slots for smaller expansion cards (Wi-Fi, USB adapters).
3. PCI: Two legacy 32-bit PCI slots.

Part 8: Frequently Asked Questions (Manual Extract)

Q: Can I use this board with Windows 10?
Manual answer (implied): No official drivers for G41 IGP beyond Vista. But community solutions exist: use the “Snappy Driver Installer” for G41 chipset drivers. A discrete GPU is recommended.

Q: Why does my CPU run at lower multiplier?
Manual answer (p. 35): SpeedStep (EIST) reduces multiplier when idle. Disable in BIOS > Cell Menu > Intel EIST if benchmarking.

Q: Where is the CMOS battery?
Manual answer (p. 10): CR2032 battery located adjacent to the PCIe slot, below the ICH7 heatsink.

Q: Does this board support Core 2 Extreme?
Manual answer: Yes – QX6850, QX6800, but only with BIOS v1.5 or higher. Not recommended due to thermal limits.

Q: Can I boot from a USB drive?
Manual answer: Yes – press F11 at POST for Boot Menu. Must set “USB Legacy Support” to Enabled.

6. Front Panel Connector (The "HP" Layout)

If you are trying to put this board into a non-HP case, this is the manual info you actually need: The front panel pins (Power LED, Power Switch, Reset Switch) are non-standard. On a standard motherboard, these are individual pins. On the MS-7613, HP often grouped them into a single block connector.

• Pinout (Standard Layout):
  • Power LED: Pins 1 & 3 (Usually the green light).
  • Power Switch: Pins 6 & 8.
  • Reset Switch: Pins 5 & 7.
  • Tip: If you don't have the HP harness, you can short pins 6 & 8 with a screwdriver to turn the board on.