Lenel Lnl3300m5 Installation Manual Upd Top !new! [ Fast - 2026 ]

Lenel LNL-3300-M5 is an Intelligent System Controller designed specifically for migrating legacy CASI M5 and M3000 systems to the Lenel OnGuard platform. It acts as a direct "plug-compatible" replacement for legacy CASI CPUs and power/communication boards. Key Technical Specifications Operating Voltage: 12 to 24 VDC (± 15%). Current Consumption: 500 mA maximum.

Supports up to 32 board addresses and can store up to 50,000 events in non-volatile memory. Communication:

On-board 10/100 Ethernet for host connection and RS-485 for downstream device communication. Hitron Bina Teknolojileri Installation Steps Hardware Migration:

Power down the legacy controller and unplug all field wiring from legacy boards. Remove the legacy CASI CPU and Power/Comm Board. Insert the LNL-3300-M5 into the backplane and reconnect the field wiring.

Position the module over corresponding spacers in the enclosure and depress until it snaps into place.

Connect dedicated inputs for cabinet tamper (TMP) and power failure (FLT) status. Wiring Requirements: Use 18 AWG twisted pair.

Use 24 AWG twisted pair(s) with shield, up to a maximum distance of 4,000 ft (1,219 m). Initial Configuration & Web Setup

To initially configure the LNL-3300-M5 via its web configuration page: DIP Switch Settings:

Set DIP switch 1 OFF, 2 ON, 3 OFF, and 4 OFF to enable the default configuration. Default IP Address: The panel defaults to 192.168.0.251 Computer Setup:

Configure your computer's IP address to the 192.168.0.x range (excluding .251).

Developing a paper or guide for the Lenel LNL-3300-M5 involves understanding its role as a migration bridge. This controller is specifically designed to replace legacy CASI M5 and M3000 CPUs, allowing users to transition to the Lenel OnGuard system without rewiring their entire infrastructure. 1. Hardware Overview

The LNL-3300-M5 is an Intelligent System Controller (ISC) that acts as the primary "brain" for access control.

Capacity: Supports up to 240,000 cardholders in local memory and 32 board addresses.

Connectivity: Features an onboard 10/100 MB Ethernet port and an external RS-485 port for downstream devices like the LNL-1320 or LNL-1100.

Compatibility: It is plug-compatible with legacy CASI power/comm boards, using the existing 12 VDC power and cabinet tamper inputs. 2. Initial Configuration Steps lenel lnl3300m5 installation manual upd top

To set up the controller for the first time, you typically access its built-in web configuration page:

Network Setup: Set your computer to a static IP in the 192.168.0.x range (avoiding .251, which is the panel's default). DIP Switch Configuration:

Set Switch 2 to ON (others OFF) and cycle power to enter configuration mode.

Once the panel reboots (approx. 30 seconds), browse to http://192.168.0.251.

Authentication: Toggle Switch 1 to ON to enable the default login: admin / password.

Finalize: Set the desired static IP for your facility's network, click "Apply Settings and Reboot," and return all DIP switches to OFF for normal operation. 3. Critical Installation Notes

Migration Rule: You cannot mix legacy CASI boards with new Lenel M Series boards in the same controller enclosure; if you upgrade the CPU to the LNL-3300-M5, all attached boards must also be converted to M Series.

Memory Erase: If the board becomes unresponsive or requires a full wipe, set Switches 1 & 2 to ON during power-up to perform a bulk erase of the configuration.

For detailed wiring diagrams and regulatory compliance (like UL 294), refer to the M Series Installation Guide (Item #DOC-1042-EN-US).

The Lenel LNL-3300-M5 Go to product viewer dialog for this item.

is a high-performance Intelligent System Controller (ISC) designed for advanced access control within the OnGuard system. Specifically engineered as a migration tool, this board provides a "plug compatible" replacement for legacy CASI M5 and M3000 controllers, allowing users to upgrade legacy systems to the modern OnGuard platform without rewiring field devices. Key Specifications and Hardware Overview LNL-3300-M5

serves as the central processing unit for the controller, managing real-time access decisions and communication with the host software. Power Requirements: Supports 12 or 24 VDC ( ±plus or minus

Memory: Includes 15 MB of on-board non-volatile flash memory and battery-backed storage for up to 50,000 events.

Capacity: Can support up to 32 board addresses and manage up to 64 downstream devices. Redundancy Design

Communication: Primary communication is via a 10/100Base-T Ethernet port. It also features secondary ports for RS-485 or RS-232 communication. Installation and Migration Process The installation of the LNL-3300-M5

is primarily focused on replacing legacy boards in an existing M5 or M3000 backplane.

Power Down: Safely power off the legacy controller and disconnect all power sources. Unplug Field Wiring

: Remove the wiring from the legacy CPU and Power/Comm boards.

Board Replacement: Remove the legacy CASI boards and insert the LNL-3300-M5 . It is designed to fit standard mounting standoffs.

Reconnect Wiring: Plug field wiring back into the compatible terminals on the LNL-3300-M5

Grounding: Ensure the board is properly grounded to protect against Electrostatic Discharge (ESD) and signal transients. Initial Web Configuration and IP Setup

To configure the controller for the first time, you must access its internal web configuration page.

Network Preparation: Set your computer's IP address to the 192.168.0.x range (excluding .251) to match the panel's default IP of 192.168.0.251. DIP Switch Settings:

To enter configuration mode: Set DIP switch 1 OFF, 2 ON, 3 OFF, and 4 OFF, then cycle power.

To enable default login: Once at the login screen, turn switch 1 ON to use the default credentials (username: admin, password: password).

Access: Open a web browser (Internet Explorer is traditionally recommended) and navigate to http://192.168.0.251.

Save and Reboot: After applying static IP or DHCP settings, return all DIP switches to the OFF position (normal operating mode) and click Apply Settings and Reboot. DIP Switch Reference Table Operating Mode Normal operating mode Enable default User Name/Password Use factory default communication parameters

The Lenel LNL-3300-M5 is an Intelligent System Controller (ISC) designed as a plug-compatible, "OnGuard-ready" replacement for legacy CASI M5 and M3000 CPU boards. This guide synthesizes key installation and configuration steps based on official Lenel hardware technical specifications. 1. Hardware Preparation and Mounting Primary Onguard Server – West Coast Secondary Onguard

Legacy Migration: Power down the existing legacy controller (e.g., M5 E, P, PX, or PXN).

Board Replacement: Unplug field wiring from legacy boards and remove them. Insert the LNL-3300-M5 into the M5/M3000 backplane.

Compatibility Note: You cannot mix legacy CASI M Series boards with Lenel M Series boards in the same controller. 2. Wiring and Electrical Connections

Primary Power: Connect a 12 VDC (± 10%) power source. The controller typically consumes 300 mA.

Monitoring Inputs: Connect the dedicated TMP (Cabinet Tamper) and FLT (Power Failure) status inputs. These are normally closed contacts. Communication Ports:

Port 0 (Ethernet): 10/100Base-T high-speed port for host communication.

Ports 2-3 (Downstream): Two-wire RS-485 ports for connecting up to 32 modules each (e.g., LNL-1320 dual-reader interfaces). 3. DIP Switch Configuration

DIP switches are read upon power-up and determine the operating mode. OFF OFF OFF OFF Normal Operating Mode ON X OFF OFF Enable default login (admin/password) OFF ON OFF OFF Use factory default communication parameters ON ON OFF OFF Use Lenel default communication parameters 4. Initial Web Configuration LNL-3300-M5 | Stebilex

Redundancy Design

Primary Onguard Server – West Coast
Secondary Onguard Server – East Coast
M5s automatically fail over if primary is unreachable.

Step 1: Mounting the Controller

Secure the backplate to a UL-listed enclosure (e.g., LNL-5000).
Snap the LNL-3300M5 board onto the standoffs.
Ensure the ground lug is connected to the facility earth ground.

Adding the Controller in Onguard

Open Hardware Configuration.
Right-click on the target Communication Server.
Select Add Hardware > LNL-3300 Series.
Enter the IP address and the Activation Code (found on the sticker on the back of the board).
Synchronize the hardware. The LED labeled CPU should change from blinking amber to solid green.

Chapter 4: Network Configuration & the "UPD Top" Firmware Process

The most searched segment of the lenel lnl3300m5 installation manual upd top revolves around updating the firmware and setting the IP.

Step 5: Input Devices (Door Position & REX)

Door Position Switch (DPS): Terminals IN1 (GND and SIG).
Request to Exit (REX): Terminals IN2. Supervision: Use 1K or 2.2K EOL resistors depending on your Onguard configuration (default is 1K for “Normally Closed”).

Final Quick Reference Card (Save this section)

Default IP: 192.168.0.250:8443
Default Credentials: lenel / lenel
Wiring Torque: Terminals require 5-7 in-lbs maximum.
Firmware Tool: Lenel Device Administrator (LDA) v3.2+
Support: Contact Lenel Technical Support with the UPD version number ready.

For the most current revision of the lenel lnl3300m5 installation manual, always log in to the official Lenel Partner Portal. The hardware is powerful—but only the correct installation unlocks its full potential.

Need a PDF copy of this guide? Use your browser’s “Print to PDF” function for a field-ready reference.

4. Addressing (DIP Switches)

Set the module address (1–16) via SW1 (binary).
Example:

Address 1: SW1-1 ON, others OFF
Address 2: SW1-2 ON, others OFF
Match the address in OnGuard software under “Hardware Configuration.”

Replacing a Faulty Unit (Hot Swap)

Per the UPD Top guide:

Remove power from the old unit.
Remove the SD card (located under the main board) and insert it into the new LNL-3300M5. This retains the hardware address.
Mount the new board, reconnect power, and synchronize in Onguard. No re-addressing is required.