Lava Benco V90 Ae9120 Flash File S160 Hang Logo New [DIRECT]

When dealing with issues like a device hanging on the logo screen, a common solution is to flash the device with its stock firmware or a compatible ROM. However, before proceeding with any actions, ensure you have a few things in place:

Backup Your Data: If possible, back up your data. Flashing a device can erase all data on the device.
Charge Your Device: Ensure your device has a significant amount of charge. lava benco v90 ae9120 flash file s160 hang logo new
Understand the Risks: There are risks involved with flashing a device, including the potential for bricking your device if done incorrectly.

Here is a general guide on how to approach this: When dealing with issues like a device hanging

Requirements

Windows PC (recommended)
USB cable (original or good quality)
Power source with charged battery (>= 50%)
drivers: MediaTek (MTK) VCOM USB drivers installed
Flash tool: SP Flash Tool (compatible version)
Scatter file and S160 firmware package for Lava Benco V90 (AE9120)
Optional: MTK_CDC drivers or PDAnet if needed for certain driver issues

3. Key Specifications of Lava Benco V90 (AE9120)

To ensure you’re working on the right device, verify these specs:

Important: The flash file for "S160" is not interchangeable with S159 or S161. Always match the exact build.

Prerequisites for Flashing

Flashing firmware is a technical process. Ensure you have the following ready:

Windows PC: The flashing tools generally require a Windows operating system (Windows 7/8/10/11).
USB Data Cable: A quality cable ensures the connection doesn't drop during the process.
Device Drivers: You must install the specific MTK (MediaTek) USB VCOM or Preloader Drivers for the Lava Benco V90 so the computer can recognize the device.
Flash Tool: This device likely uses the SP Flash Tool (Smart Phone Flash Tool) or a proprietary factory tool.
Backup: If your device had important data, note that flashing the S160 firmware will likely wipe user data.

✅ Step 5: Alternative – Full format & download

In SP Flash Tool: Memory Test → OK → Format → Format whole flash (except bootloader region) → then Download.

Step-by-step flashing (SP Flash Tool)

Launch SP Flash Tool as Administrator (flash_tool.exe).
Click "Scatter-loading" and browse to the firmware folder. Select the scatter.txt file.
SP Flash Tool will load partition list and file paths. Verify files are present and correct.
Recommended: Uncheck "preloader" unless you have the exact matching preloader for the device; flashing an incorrect preloader can brick the phone.
Select the appropriate download option:
- Use "Download Only" to flash system/boot/recovery (keeps userdata if successful).
- Use "Format + Download" or "Firmware Upgrade" if the device requires a full re-write. "Firmware Upgrade" is safer than Format+Download when moving between certain builds.
Click "Download" (green arrow).
Power off the phone. Remove battery if removable (for many devices), or ensure it's fully powered off.
Connect phone to PC via USB while holding required key combo (usually Volume Down or Volume Up) if needed; otherwise, just connect the powered-off phone.
SP Flash Tool should detect the device and begin flashing. A progress bar will display; wait until a green checkmark appears indicating success.
Disconnect the phone and attempt to boot. First boot may take several minutes.

Introduction

If you are a mobile repair technician or a Lava Benco V90 user, you might have encountered a frustrating problem: the device powers on, shows the boot logo, and then gets stuck indefinitely. In technical terms, this is known as a "boot loop" or "hang logo" issue. For the specific model Lava Benco V90 (AE9120) with firmware version S160, this problem has become increasingly common.

The most reliable solution? Flashing the device with a new, verified flash file (stock firmware). This article serves as a complete guide to understanding, downloading, and installing the correct Lava Benco V90 AE9120 S160 Hang Logo New Flash File using tools like SP Flash Tool.