The Huawei USB COM 1.0 Driver is a critical system utility used primarily for servicing, unbricking, or flashing Huawei smartphones powered by HiSilicon Kirin processors. When a device is "hard-bricked" or placed into test point mode, it is recognized by a Windows PC as "HUAWEI USB COM 1.0." Key Technical Details
Purpose: Enables communication between a PC and a Huawei device in its lowest-level boot state (Emergency Download Mode/USB COM 1.0). Common Use Cases:
Unbricking: Recovering devices that won't boot into the OS or Fastboot.
Firmware Flashing: Writing software to the device via tools like SigmaKey, Chimera, or EFT Pro. FRP Removal: Bypassing Factory Reset Protection. Bootloader Repair: Fixing corrupted bootloader partitions. Installation Guide
Disable Driver Signature Enforcement: On Windows 10 or 11, you must often disable driver signature enforcement via "Advanced Startup" settings to allow the driver to initialize correctly.
Hardware Connection: The phone must be connected via a test point (physically shorting two points on the motherboard) while plugging in the USB cable. Manual Update: Open Device Manager.
Locate the "Unknown Device" or "HUAWEI USB COM 1.0" under Ports (COM & LPT). huawei usb com 1.0 driver.zip
Right-click → Update Driver → Browse my computer → Select the folder where you extracted the .zip file. Safety & Compatibility
Compatibility: Supports Windows 7, 8, 10, and 11 (both x86 and x64 architectures).
Security Risk: Because these drivers are often hosted on third-party GSM hosting sites rather than official Huawei portals, always scan the .zip file with updated antivirus software (like VirusTotal) before execution.
Required Tools: The driver itself does not flash the phone; it only creates the bridge. You will need service software (e.g., HiSuite, IDT, or professional GSM tools) to perform actual repairs. Troubleshooting
Code 10 Error: Usually caused by improper driver signature enforcement or a faulty USB cable.
Not Recognized: Ensure you are using a high-quality data cable and that the test point short is making solid contact. The Huawei USB COM 1
The Huawei USB COM 1.0 driver is a critical utility used primarily by technicians and advanced users for servicing Huawei devices. It allows a computer to communicate with a phone that is in EDL (Emergency Download Mode) or has been connected via a hardware "test point" for low-level tasks like unbricking or flashing firmware . Key Technical Details
Purpose: Resolves the "USB SER" or "Other Device" error in Windows Device Manager when a device is in service mode .
Supported OS: Windows 7, 8, 8.1, 10, and 11 (both 32-bit and 64-bit) .
Hardware ID: Typically identified as USB\VID_12D1&PID_3650&MI_00 or USB\VID_12D1&PID_3609 .
Driver Version: Commonly version 2.0.6.725 (released 2016) or newer . How to Install (Reported Steps)
Most "good reports" and guides suggest a manual installation process because the driver is often unsigned or not automatically recognized by Windows : What Is the Huawei USB COM 1
The Huawei USB COM 1.0 driver is a Windows-based communication driver that allows a computer to recognize a Huawei smartphone or tablet when it is connected in "Qualcomm Download Mode" (also known as Emergency Download Mode, DLOAD, or QDLoader 9008 mode). Once installed, the device appears in Windows Device Manager under "Ports (COM & LPT)" as "Huawei USB COM 1.0", assigned to a specific COM port number.
This mode is not the standard MTP or ADB connection used for file transfer or debugging. Instead, it is a low-level, pre-boot state typically used when:
| Aspect | Detail | |--------|--------| | Chipset | Qualcomm-based Huawei devices (HiSilicon Kirin devices do NOT use this driver) | | Models | Huawei P series, Mate series, Honor (pre-2021), some Y series with Snapdragon | | Alternate Modes | Not required for HiSuite, ADB, Fastboot, or dload folder upgrade | | Risks | Incorrect flashing can permanently damage device — use only with proper firmware |
The driver is designed for Windows 7, 8, and 10 (32/64-bit). It requires digital signature enforcement to be disabled on newer Windows versions to install correctly.
You do not need the huawei usb com 1.0 driver.zip for a working modem. You need it if:
If you cannot get huawei usb com 1.0 driver.zip to work, or you're concerned about security, use these modern methods:
Huawei - Ports - 2.0.3.7. Uninstall the device, scan for hardware changes, and let Windows Update fetch the driver. It often works for download mode.option and usbserial modules recognize the Huawei download mode natively. Use modprobe usbserial vendor=0x12d1 product=0x1446.