The Ericsson Radio 2460 is a dual-band remote radio unit (RRU) within the Ericsson Radio System portfolio. It is designed primarily for low-band coverage and capacity, specifically supporting frequencies such as 700MHz, 800MHz, and 900MHz. Key Technical Specifications
The following technical details are derived from industry deployment data and Ericsson’s radio portfolio:
Frequency Support: Supports low-band spectrum including 700MHz (n28), 800MHz (B20), and 900MHz (B8).
Radio Standards: Multi-standard capability supporting GSM, WCDMA, LTE, and 5G (FDD).
Receive Pathways: Notable for providing 4-way receive (4Rx) capability, which enhances uplink performance and coverage in rural and moderate urban areas.
Cooling: Features a fanless, passive cooling design to reduce maintenance and increase reliability.
Interface: Supports standard CPRI and packetized fronthaul (eCPRI) for integration with Cloud RAN and purpose-built Ericsson RAN Compute products. Design and Deployment Features
Modular Installation: Uses Ericsson’s unique one-bolt installation system, allowing for flexible mounting on rails, walls, poles, or ceilings.
Efficiency: Powered by Ericsson Silicon, the radio is designed for high energy efficiency and a reduced carbon footprint compared to previous generations.
Interference Mitigation: Includes built-in PIM (Passive Intermodulation) cancellation to reduce uplink interference when multiple signals share the same antenna.
Sustainability: Part of a portfolio that targets up to a 50% reduction in embodied carbon footprint. Product Documentation
For detailed installation and maintenance procedures, engineers can refer to the Radio 2460 Installation Guide on Scribd, which details required tools (e.g., Torx T30, torque wrenches) and safety precautions. Radio 2460
with newer Radio 44xx series models or see specific power consumption ratings for this unit?
Install Radio 2460 | PDF | Electrical Connector | Screw - Scribd
Ericsson Radio 2460 (part number KRC161831/1) is an outdoor macro remote radio unit (RRU) designed to support multi-standard low-band deployments. It is a key component of the Ericsson Radio System designed for wide-area coverage and network modernization. Sparepart4you BV Key Technical Specifications
The following specifications are commonly found in the product's datasheet and technical documentation: Sparepart4you BV Specification Radio Type Outdoor macro remote radio unit Supported Bands (900 MHz), (800 MHz), Duplex Mode Frequency Division Duplex (FDD) Technology LTE (4G), 5G NR (low-band) Operational Temp Durable aluminum alloy housing Installation and Hardware According to the official installation manual
for the Radio 2460, deployment requires specific tools and procedures: Mounting Options
: Flexible mounting on rails, walls, or poles using Ericsson's one-bolt installation system.
: Uses intelligent thermal management (passive cooling) for high efficiency without the need for external fans. Connectivity
: Features low-latency integration for both 4G and 5G agile networks. Required Tools
: Standard installation typically requires TORX T20/T30 bits, 10mm/13mm sockets, and torque wrenches (5–22 Nm). Core Benefits Simplified Architecture
: Consolidates multiple low-frequency bands into a single unit, reducing site hardware footprint. Enhanced Coverage
: Optimized for rural and suburban layers where signal penetration is critical. Energy Efficiency
: Leverages state-of-the-art silicon and thermal management to minimize power consumption. Sparepart4you BV configuration or a replacement part for this radio unit?
Install Radio 2460 | PDF | Electrical Connector | Screw - Scribd
Ericsson Radio 2460 (part of the Ericsson Radio System) is a low-band, multi-band remote radio unit (RRU) designed to provide wide-area coverage and excellent signal penetration for LTE (4G) networks. It is particularly effective for rural and suburban deployments where long-range macro-cell performance is critical. The Pulse of the Valley: A Technical Tale
The engineers in the small valley of Oakhaven called it "The Silent Guardian." To everyone else, it was just the Ericsson Radio 2460 ericsson ers 2460 datasheet
, a 37.5 kg block of aluminum alloy bolted to a rail at the top of the ridge.
For years, Oakhaven was a "dead zone." The town sat deep in a geographic bowl where signals from the distant city simply couldn't reach. But when the local carrier decided to modernize, they didn't just want a signal; they wanted a foundation. They chose the Radio 2460 because it spoke the three "low-band languages" the valley needed: Band 8 (900 MHz) Band 20 (800 MHz) Band 28 (700 MHz) On installation day, the technician, Sarah, appreciated the one-bolt installation
system. As she tightened the final 5 mm bolt and connected the SFP modules , she knew that even if the temperature dropped to in the winter or hit in a summer heatwave, the 2460’s passive cooling
would keep it humming without a single mechanical fan to fail. Once powered up at its standard
, the radio began its work. Its 2Tx/4Rx architecture pushed data across the valley floor, penetrating thick brick walls and reaching basement workshops that hadn't seen a "bar" of signal in a decade. It wasn't just about faster downloads; it was the spectrum efficiency. By combining three bands into one hardware footprint, the carrier saved on site rental and energy, using roughly to light up an entire township.
Now, as the sun sets over Oakhaven, the Radio 2460 sits silently on its pole, resisting wind loads of up to
. It doesn't look like much, but for the people below, it is the invisible thread connecting them to the rest of the world. Key Specifications from the Datasheet Radio Type : Outdoor macro remote radio unit. Frequency Support : Triple-band (B8, B20, B28B). Dimensions : 37.5 kg. Power Consumption : Typical 1215 W. Environment : Operating range from futuristic story involving its 5G-ready capabilities, or perhaps a technical breakdown of its mounting options? KRC161831/1 – Radio 2460 24B8 / 24B20 / 24B28B M01
The Ericsson Radio 2460 is a critical component within the Ericsson Radio System (ERS) portfolio, a modular end-to-end radio access network (RAN) solution designed to support multi-standard cellular technology from 2G to 5G. As a multiband radio unit, the 2460 is engineered for high performance, scalability, and energy efficiency, enabling operators to manage increasing data traffic while maintaining a minimal site footprint. Key Technical Specifications
The Radio 2460 is characterized by its compact design and robust technical capabilities, as detailed in site manager handouts and technical datasheets:
Radio Architecture: Features a 4-transmitter and 4-receiver (4T/4R) configuration, supporting advanced Multiple-Input Multiple-Output (MIMO) technology to enhance spectral efficiency and data throughput.
Operating Bandwidth: Designed as a dual-band radio, it allows operators to consolidate equipment by supporting multiple frequency bands—such as Band 1 and Band 3—within a single unit.
Physical Dimensions: The unit typically measures approximately in height, in width, and in depth (without a fan), weighing roughly
Power and Environmental: Operates within a standard voltage range of and is built to withstand extreme temperatures ranging from -40∘Cnegative 40 raised to the composed with power C +55∘Cpositive 55 raised to the composed with power C Installation and Integration
Versatility is a core feature of the ERS 2460, allowing for diverse deployment scenarios. According to installation guides, the unit can be mounted on rails, walls, poles, or even integrated directly behind antennas. The ERS rail system facilitates rapid, "one-bolt" installation, which significantly reduces the time and labor required at the cell site.
The unit utilizes eCPRI interfaces for high-speed packet fronthaul, ensuring compatibility with modern Open RAN architectures and facilitating a smooth transition to 5G Standalone (SA) networks. Performance Benefits
Integrating the Radio 2460 into a network provides several advantages for telecommunications providers:
Energy Efficiency: As part of the wider ERS effort, these radios are optimized to reduce power consumption by up to 15% compared to previous generations.
Scalability: The modular nature of the Ericsson Radio System allows for easy capacity upgrades through software activation codes and hardware expansion.
Low Maintenance: The use of passive cooling systems (no internal fans) minimizes mechanical failure points and long-term maintenance costs. Ericsson radios for capacity and energy efficiency
| Terminal | Label | Description | | :--- | :--- | :--- | | 1 | V+ (Main) | +12 to 48 VDC | | 2 | V- (Main) | DC Return | | 3 | Chassis GND | Earth Ground | | 4 | V+ (Redundant) | Secondary DC feed | | 5 | V- (Redundant) | Secondary return |
The Ericsson ERS 2460 datasheet reveals a rugged, capable industrial switch that was ahead of its time for edge PoE deployments. In 2025, it remains a viable option for:
However, for greenfield deployments, seek current hardened switches from Cisco, Siemens, or Moxa—but keep a copy of the ERS 2460 datasheet handy if you maintain legacy Ericsson networks. Its fanless reliability and dual DC input remain gold standards that many modern “industrial” switches still try to match.
Final Note for Searchers: If you specifically need the original PDF datasheet from Ericsson, include "filetype:pdf" in your search alongside the exact model number (e.g., "ERS 2460-24T-PWR filetype:pdf"). Archive.org and industrial networking forums are your best resources today.
This article is for informational purposes. Always consult official installation manuals and safety guidelines before deploying network hardware.
The Ericsson Radio 2460 is a multiband unit within the Ericsson Radio System (ERS) that supports 5G, LTE, and WCDMA technologies, designed for efficient deployment. It features 4.3-10 antenna connectors, SFP modules for CPRI, and flexible mounting options for various installation scenarios. For more details, visit Scribd. Ericsson Radio System
The Ericsson Radio 2460 is a low-band, multi-band remote radio unit (RRU) within the Ericsson Radio System designed primarily for LTE macro-cell coverage. It is a triple-band solution that integrates Bands 8 (900 MHz), 20 (800 MHz), and 28 (700 MHz) into a single unit, making it a "street macro" or macro-grade choice for rural and suburban deployments where deep indoor penetration and wide-area coverage are essential. Technical Specifications and Architecture The Ericsson Radio 2460 is a dual-band remote
Based on available data from sources like sparepart4you.com and technical handouts: Part Number: KRC 161 831/1.
Radio Configuration: Standard configurations include 2T2R or 2T4R, supporting LTE MIMO.
Supported Bandwidths: 5, 10, 15, and 20 MHz, depending on the specific band and software configuration. Interfaces:
Fronthaul: Optical fiber interfaces using CPRI (Common Public Radio Interface), typically rated at 10.3 Gbps.
Connectors: Standard 4.3-10 antenna connectors for RF paths.
Cooling & Maintenance: Features a passive convection cooling system (fanless design) to reduce moving parts and maintenance requirements.
Environmental Operating Range: Built for extreme outdoor conditions from −40 °C to +55 °C. Performance and Key Features
Spectrum Consolidation: By supporting three low-frequency bands (700/800/900 MHz), it significantly reduces the amount of hardware needed on a tower, lowering rental costs and site complexity.
Ericsson Silicon Integration: Like other modern ERS radios, it utilizes Ericsson Silicon for high processing capacity and improved energy efficiency, often consuming 30–60% less power than previous generations.
Network Compatibility: It is frequently paired with Baseband 6631 units in low-capacity or modernization configurations to support GSM, UMTS, and LTE concurrently.
Modernization Ready: While primarily an LTE unit, it is part of a portfolio that supports Spectrum Sharing and "Deep Sleep" energy-saving modes, allowing it to hibernate during low-traffic periods (e.g., at night) to cut OPEX. Installation and Physical Footprint
The unit is designed for rapid deployment with Ericsson's rail mounting system, which uses a unique one-bolt installation method. It can be mounted on poles, walls, or masts. Mounting Wall, Pole, Mast, or Rail Typical Use Rural, suburban, and nationwide LTE coverage layers Connectivity SFP modules for optical fronthaul Durability Outdoor macro-grade enclosure The key components of high-performing radios - Ericsson
The Ericsson Radio 2460 (KRC161831/1) is a versatile low-band, multi-band remote radio unit (RRU) part of the Ericsson Radio System (ERS) portfolio. Engineered specifically for wide-area coverage and network modernization, it allows operators to consolidate multiple frequency bands into a single compact hardware platform. Key Technical Specifications
The Radio 2460 is designed for high performance in macro-cell deployments with the following core technical attributes:
Frequency Bands: Supports LTE deployments in Bands 8 (900 MHz), 20 (800 MHz), and 28 (700 MHz).
Operating Modes: Capable of supporting GSM, WCDMA, LTE, and 5G mode using FDD and TDD.
Physical Dimensions: Typically measures approximately 553 x 398 x 190 mm with a weight of roughly 37.5 kg (varying slightly by sub-model).
Output Power: Supports a total output power of 320W, typically configured for 2x2T/4R operations.
Connectivity: Equipped with 4x4.3-10 RF connectors and 2x10G FullAXS SFP/fiber optic ports for high-speed fronthaul. Advanced Features & Technology
The Radio 2460 integrates several of Ericsson's modern RAN (Radio Access Network) technologies to optimize efficiency:
Ericsson Spectrum Sharing (ESS): Designed to support 5G NR and spectrum sharing, allowing for a smooth transition from 4G to 5G without needing dedicated spectrum.
Energy Efficiency: Features passive cooling (no internal fans) to reduce maintenance and lower the site's energy footprint.
Fronthaul Capabilities: Supports eCPRI (Packet Fronthaul), which is essential for modern, high-capacity packet-based transport networks.
Open RAN Ready: Built with an architecture that is prepared for Open RAN environments. Installation & Deployment
The ERS 2460 is highly flexible regarding where and how it can be deployed on a site:
Mounting Options: Can be installed on poles, walls, or rails using standard ERS brackets. It can also be mounted directly behind or below an antenna to minimize cable loss. Terminal Block Power Pinout | Terminal | Label
Ease of Installation: Utilizes Ericsson's unique one-bolt installation rail system, which significantly speeds up site deployment and reduces technician labor.
Harsh Environments: Engineered to operate in extreme temperature ranges from -40°C to +55°C and is built to withstand high wind loads of up to 320 N at 50 m/s. Typical Use Cases
Operators deploy the Radio 2460 primarily in scenarios requiring extensive coverage and reduced site complexity:
Rural & Suburban Coverage: Ideal for nationwide coverage layers due to its use of low-frequency bands that penetrate buildings and travel long distances.
Network Modernization: Used to replace multiple legacy single-band radios with one multi-band unit, reducing the total hardware footprint and rental costs on towers.
Macro-Cell Capacity: Provides robust 4T4R performance for macro sites while maintaining energy efficiency. KRC161831/1 – Radio 2460 24B8 / 24B20 / 24B28B M01
The Ericsson Radio 2460 is a multiband radio unit typically used in Ericsson Radio System (ERS) deployments for high-capacity mobile networks. While a single consolidated "datasheet" PDF is often proprietary, technical details and installation specifications are available through various site deployment and installation guides. Key Technical Specifications
Radio Type: Multiband Outdoor Radio (frequently deployed alongside Radio 4480).
Capacity: High-capacity RAN compute unit prepared for NR (5G), LTE, and LTE Evolution. Mounting Options: Rail mounting on walls or poles. Dual ERS bracket on poles. Antenna-integrated or separate installation alternatives. Power & Connectivity: Power Supply: Standard -48V DC.
Interfaces: Equipped with SFP slots (up to 25Gbps), CPRI ports for fronthaul, and external alarm ports. Documentation Links
Installation Guide: Detailed instructions for tools, safety, and physical setup can be found in the Install Radio 2460 Manual.
Deployment Handout: For site managers planning multiband deployments, the ERS Handout for Radios 2460 & 4480 provides operational context.
Install Radio 2460 | PDF | Electrical Connector | Screw - Scribd
The Ericsson Radio 2460 is a compact, passively cooled 2T4R dual-band remote radio unit designed for low-band (700/800/900 MHz) multi-standard networks including GSM, WCDMA, LTE, and 5G NR. Featuring one-bolt installation and versatile mounting options, this unit offers enhanced uplink performance and is compatible with Baseband 6631/6651 for high-capacity site deployment. For more details, visit Baseband 6631 & 6651 Configurations | PDF - Scribd
Ericsson Radio 2460 (also known as KRC161831/1) is a high-performance, multiband remote radio unit designed for the Ericsson Radio System
. It is engineered to support low-band LTE deployments, providing wide-area coverage and long-range macro-cell performance. Sparepart4you BV Key Technical Specifications
The following technical details are characteristic of the Radio 2460 deployment: Supported Frequency Bands : Specifically designed for Band 8 (900 MHz) Band 20 (800 MHz) Band 28B (700 MHz) Radio Configuration : Features a (2 Transmitters / 4 Receivers) triple-band configuration. Physical Dimensions : 553 mm (Height) x 398 mm (Width) x 190 mm (Depth). : Approximately (without fan). Power Consumption : Rated at approximately Operating Voltage : Standard range of -38.0 to -58.5 VDC Operational Temperature : Built to withstand environments from -40°C to +55°C Sparepart4you BV Features and Benefits Site Optimization
: By combining three low-frequency bands into a single unit, it reduces the physical hardware footprint on-site and simplifies overall site architecture. Enhanced Coverage
: Ideal for rural and suburban areas where deep signal penetration and long-range connectivity are critical. Ericsson Silicon : Powered by custom-made Ericsson Silicon
, it optimizes energy consumption and performance compared to standard hardware. Installation Flexibility : Supports various mounting alternatives, including rail mounting ERS bracket mounting
, facilitating easier deployment in diverse site environments. Installation and Maintenance Manuals for the Radio 2460 highlight specific requirements for field technicians: : Requires standard and specialized tools such as Torx T20/T30 , various sockets (10 mm, 13 mm), and a torque wrench (5–22 Nm) for secure fastening. Connectors : Utilizes 4.3-10 connectors for antenna paths and a DIN connector for external alarms. Maintenance
: Designed with modularity in mind to speed up initial assembly and subsequent field servicing. software compatibility for this radio model?
Install Radio 2460 | PDF | Electrical Connector | Screw - Scribd
| Parameter | Specification | | :--- | :--- | | Operating temperature | 0°C to 50°C (32°F to 122°F) – standard models | | Storage temperature | -40°C to 70°C (-40°F to 158°F) | | Operating humidity | 10% to 90% (non-condensing) | | MTBF (Mean Time Between Failures) | > 200,000 hours | | Noise level (fan) | < 45 dBA (varies by load, especially PoE models) | | Cooling | Internal variable-speed fans, side-to-rear airflow |
The ERS 2460 runs Ericsson’s Enterprise Operating System (EOS) legacy stack—a CLI-centric, stable L2+ platform.
The ERS 2460 is not a chassis-based core switch. Instead, it is a stackable, Layer 2+ (L2+) Gigabit Ethernet switch designed for:
Unlike data center switches focused on low-latency fabric, the ERS 2460 prioritizes manageability, security, power efficiency, and deployment flexibility.