Autocraft Battery Charger Ac-60cr Manual ~upd~ 【Tested & Working】

This report summarizes the features, operating instructions, and safety protocols for the Autocraft AC-60CR Battery Charger

, an analog automotive charger with engine start capabilities. Product Overview Autocraft AC-60CR

is a 12V manual/analog battery charger designed for regular and AGM lead-acid batteries

. It is primarily used for standard automotive charging and emergency engine starting. Harbor Freight Key Features and Specifications Charging Modes

: Features multiple output settings, typically including a slow charge ( ), medium charge ( ), and a high-current engine start mode ( or higher depending on variant). Compatibility

: Supports Regular (flooded/maintenance-free) and AGM batteries. Do not use with Gel batteries Analog Ammeter

: Displays the current drawn from the charger in real-time. As a battery reaches full charge, the needle should move toward 0A. Engine Start

: Provides a temporary high-amperage boost to jump-start a vehicle with a weak battery. images.thdstatic.com Operating Instructions Charging a Battery in the Vehicle Preparation autocraft battery charger ac-60cr manual

: Ensure the vehicle is off and the area is well-ventilated. Connection : Connect the Red (Positive) clamp to the positive battery post first. Then, connect the Black (Negative)

clamp to a solid metal part of the vehicle chassis away from the battery.

: Select the appropriate battery type (Regular/AGM) and charge rate (e.g., 2A for slow/maintain, 10A for fast). : Plug the charger into a grounded AC outlet. Monitoring

: Since this is a manual charger, monitor the ammeter. Unplug the charger once the needle drops to zero or near zero to avoid overcharging. Using Engine Start Connect the clamps as described above. Set the switch to Engine Start

Wait for the specified duration (usually 3–5 minutes) to let the battery absorb a surface charge.

Crank the engine for no more than 5 seconds. If it doesn't start, wait 3 minutes before trying again to prevent the charger from overheating. images.thdstatic.com Safety and Troubleshooting Automatic Battery Charger

Autocraft Battery Charger AC-60CR Manual Model: AC-60CR Input Voltage: 120V AC Output Voltage:

Introduction

Congratulations on purchasing the Autocraft Battery Charger AC-60CR! This manual provides detailed information on the safe and effective use of your new battery charger.

Specifications

• Model: AC-60CR
• Input Voltage: 120V AC
• Output Voltage: 6V/12V DC
• Charging Current: 6A/3A
• Battery Type: Lead-Acid (Flooded, Gel, and AGM)

Components and Accessories

• Autocraft Battery Charger AC-60CR unit
• User manual
• Input power cord
• Output charging cables (red and black)

Safety Precautions

1. Read the manual carefully before using the charger.
2. Ensure proper ventilation around the charger during use.
3. Avoid exposure to water or excessive moisture.
4. Keep children away from the charger.
5. Never touch the charger with wet hands or while standing on a conductive surface.

Operating Instructions

1. Connect the charger to a power source: Plug the input power cord into a 120V AC outlet.
2. Identify the battery type: Ensure the battery type matches the charger's specifications (lead-acid, flooded, gel, or AGM).
3. Connect the charging cables:
   • Attach the red (positive) charging cable to the battery's positive terminal.
   • Attach the black (negative) charging cable to the battery's negative terminal.
4. Select the charging mode:
   • 6V/12V selector switch: Choose the correct voltage for your battery.
   • Charging current selector switch: Choose the desired charging current (6A or 3A).
5. Start the charging process: Press the "Start" button.
6. Monitor the charging process: The charger's LED display will show the charging status.

LED Display Indicators

• Charging mode: Green LED light indicates charging mode.
• Battery status: LED display shows battery voltage, charging current, and error codes (if any).

Error Codes and Troubleshooting

• Error Code E01: Battery voltage too low. Check battery connections and voltage.
• Error Code E02: Battery voltage too high. Check battery voltage and charging settings.
• Error Code E03: Overheating. Allow the charger to cool down.

Maintenance and Storage

1. Clean the charger regularly with a dry cloth.
2. Store the charger in a dry, well-ventilated area.
3. Avoid storing the charger near flammable materials.

Warranty Information

The Autocraft Battery Charger AC-60CR is backed by a limited warranty. For warranty details, please refer to the warranty card or contact our customer support team.

Conclusion

Your Autocraft Battery Charger AC-60CR is designed to provide safe and efficient charging for your lead-acid batteries. By following the guidelines and precautions outlined in this manual, you can ensure a long and trouble-free charging experience. If you have any questions or concerns, please don't hesitate to contact our customer support team. Happy charging!

Step 2: Connecting the Clamps

Critical: Always connect clamps before plugging the charger into AC power. Components and Accessories

• Positive (RED) clamp: Connect to the POSITIVE (+) terminal of the battery.
• Negative (BLACK) clamp: Connect to the NEGATIVE (-) terminal of the battery.
• For vehicle charging (battery installed): Connect the negative clamp to a solid metal part of the chassis, away from the battery and fuel lines.

9. Where to Find the Real Manual (Verifiable)

The official AutoCraft AC-60CR manual is no longer hosted by Advance Auto Parts for this discontinued model, but you can still find copies:

1. Manualslib.com – Search “AutoCraft AC-60CR” – user‑uploaded PDFs.
2. DieHard manuals – The AC-60CR is nearly identical to DieHard 200.71230 and 200.71231 (same electronics).
3. eBay / Amazon listings – Some sellers include scanned manuals.
4. Internet Archive (archive.org) – Search “AutoCraft battery charger manual”.

Step 4: Plugging In

Insert the AC plug into a grounded 120V outlet. The charger will run a self-diagnostic for 3-5 seconds.

Maintenance & Storage

• Store in a dry, cool place.
• Inspect cables and clamps for wear; replace if insulation or jaws are damaged.
• Wipe off acid residue and corrosion from contacts.