Since specific technical documentation for "Alcor Micro FA00 - F W 3613" is scarce (likely indicating a specific internal firmware revision for a USB flash controller or card reader), this blog post is tailored for an audience of IT technicians, data recovery specialists, and electronics hobbyists who have encountered this specific string in their logs or hardware tools.
Here is a draft for the blog post.
Let's break the string into its components:
| Component | Meaning |
|-----------|---------|
| ALCOR MICRO | The manufacturer of the USB controller chip. Alcor Micro (often stylized as AlcorMicro) is a Taiwanese semiconductor company known for budget-friendly USB 2.0/3.0 flash drive controllers, card readers, and KVM switches. |
| UNKNOWN | Windows cannot retrieve the device’s friendly name or model from its firmware. This usually indicates a corrupted or missing VID/PID (Vendor ID/Product ID). |
| FA00 | This is the Product ID (PID). In Alcor’s ecosystem, FA00 typically refers to a generic or uninitialized flash drive controller—often the AU699X, AU698X, or SC908 (Alcor branded) series. It can also appear when the NAND flash memory is not detected. |
| F/W 3613 | Firmware version 3613. This is a relatively old firmware (likely from ~2012–2015) for USB 2.0 controllers. Newer Alcor firmware versions are 5xxx, 6xxx, or 8xxx. |
Key insight:
FA00is not a normal operational PID. A healthy Alcor flash drive would show something likeAU6989orSC908AN.FA00signals that the controller is in a firmware recovery mode, manufacturing test mode, or has lost its NAND mapping table.
Seeing “Alcor Micro Unknown FA00 - FW 3613” is usually resolvable by identifying the VID/PID, updating drivers, or using vendor tools — but proceed cautiously with firmware flashing, and prioritize data recovery if the device contains important files.
If you want, tell me which OS you’re using and provide the VID/PID string from Device Manager or lsusb output and I’ll give specific next steps.
The "Alcor Micro Unknown FA00 - F/W 3613" error is a common headache for users dealing with corrupted USB flash drives, generic thumb drives, and SD card controllers. This specific firmware (F/W 3613) and chip ID (FA00) indicate that your computer recognizes the hardware interface but cannot communicate with the memory chips inside, often resulting in a "Disk is Write Protected" or "Please Insert Disk" message.
To fix this, you generally need to perform a "low-level format" using the specific Alcor Micro Production Tool (MPTool) designed for this chipset. Understanding the Hardware
Alcor Micro is a massive manufacturer of USB bridge controllers. Their chips are found in everything from high-end Transcend drives to unbranded "freebie" sticks.
FA00: This is the controller ID. It tells the software which instruction set to use.
F/W 3613: This is the firmware version currently flashed onto the controller. If this is appearing as "Unknown," it means the firmware is corrupted or the software version you are using is too old to recognize it. Step 1: Identify Your Exact Chipset
Before downloading tools, you must confirm the hardware details. Using a generic formatter can permanently "brick" the drive.
Download a tool called ChipGenius or Flash Drive Information Extractor. Plug in your USB drive.
Look for the Controller Part-Number (e.g., AU6989SN, AU6998) and the Flash ID Code.
Note down the VID (Vendor ID) and PID (Product ID)—usually 058F and 6387 for Alcor. Step 2: Download the Correct Alcor MPTool
You cannot use a standard Windows format tool for an FA00 error. You need the Alcor Micro Production Tool.
Search for "AlcorMP" followed by your controller part number (e.g., "AlcorMP AU6989").
Look for versions released after the date of your F/W 3613 (typically versions from 2013-2015 or newer).
Reliable databases for these tools include sites like FlashBoot or USBDev. Step 3: The Repair Process (Flashing) Warning: This process will destroy all data on the drive. Run as Administrator: Open the AlcorMP.exe file.
Insert Drive: If the tool doesn't see your drive, go to "Setup" and ensure the VID/PID matches what you found in Step 1.
Load Default Profile: Most FA00 errors can be fixed by the "Optimized Capacity" or "Default" settings. Start: Click the "Start" (S) button.
Wait: The status bar will turn yellow (processing) and then green (pass). If it turns red, the memory chip itself might be physically dead. Troubleshooting Common Failures
"Too Many Bad Blocks": The NAND flash chip is wearing out. You can try setting the "Scan Level" to a deeper cycle in the AlcorMP settings to "wall off" the dead sectors.
"Controller Not Supported": You are using an older version of the MPTool. Look for a "New Style" (ALCOR_U2_MP) version of the software.
Write Protect Error: This is the primary reason people seek F/W 3613 tools. The MPTool is the only way to reset the "read-only" flag triggered by the controller's safety firmware.
💡 Pro Tip: If the software still says "Unknown," try plugging the drive into a USB 2.0 port on the back of your computer (motherboard port). USB 3.0/3.1 ports often interfere with the low-level flashing commands required by Alcor controllers. To help you find the exact software you need, tell me: What is the Controller Part-Number from ChipGenius? What is the Flash ID (the long string of letters/numbers)? Are you trying to recover data or just fix the drive?
The identifier "Alcor Micro Unknown [FA00] - F/W 3613" refers to a specific error state or hardware signature of a USB flash drive controller produced by Alcor Micro. This typically occurs when a computer's operating system or a low-level diagnostic tool can communicate with the USB controller chip but cannot identify the specific model or the NAND flash memory it is supposed to manage. The Role of the Alcor Micro Controller At the heart of every USB drive is a mass storage controller
, a small processor that manages data flow between the computer and the flash memory. Alcor Micro is a prominent manufacturer of these chips, often found in "generic" or rebranded flash drives. When a drive works correctly, it reports its specific model number (e.g., AU6989). However, if the firmware is corrupted or the chip enters a "test mode," it may display the generic [FA00] placeholder. Understanding the [FA00] and F/W 3613 Signature Unknown [FA00]
: This is not a specific model of chip but rather a status code indicating the controller's inability to recognize the attached flash memory (FID). It often appears when the drive is physically damaged or has suffered a severe firmware failure. : This represents the Firmware version
currently running on the controller. Firmware is the permanent software programmed into the hardware that tells it how to operate. Common Symptoms and Causes
When a device shows this signature, users usually experience the following: Zero Capacity : The drive appears in "Disk Management" but shows or "No Media". Write Protection
: The drive may be visible but refuses to allow any data to be saved or deleted. Device Not Recognized
: Windows may show a "USB Device Not Recognized" error popup. Solutions and Recovery
Fixing a drive in this state usually requires "Mass Production Tools" (MPTools), which are specialized software utilities used by manufacturers to format and "burn" firmware onto the chips. Identification : Users often use tools like ChipGenius to find the exact Vendor ID (VID) and Product ID (PID). Driver Reinstallation : Sometimes, simply updating or uninstalling the driver
through the Windows Device Manager can resolve basic communication errors. Firmware Reflashing : If the hardware is intact, downloading the specific Alcor MPTool
for that controller can sometimes restore the drive to a working state, though this usually erases all existing data. Are you trying to recover data from a drive showing this error, or are you looking to repair the hardware for future use?
If you are seeing Alcor Micro Unknown [FA00] - F/W 3613, your USB flash drive is likely suffering from a corrupted controller firmware. This error typically occurs when the computer recognizes the hardware but cannot communicate with the memory chips, often resulting in a "No Media" or 0 Byte status in Windows. 🛠️ How to Fix the FA00 / FW 3613 Error
This error is usually solved by "mass production" (MP), which involves re-flashing the firmware to the controller chip. 1. Identify Your Chipset alcor micro unknown fa00 - f w 3613
Before downloading tools, you must confirm the exact controller model (e.g., AU6989, AU6998).
Use a tool like ChipGenius or Flash Drive Information Extractor to find the VID (usually 058F) and PID (usually 6387). Look for the Controller model name in the report. 2. Download the Correct AlcorMP Tool
"AlcorMP" is the official factory software used to repair these drives.
Visit specialized databases like USBDev.ru to find a version compatible with your controller model.
For a 64GB drive showing FW 3613, you may need a newer version of the Alcor U2 MP or AlcorMP_UFD utility. 3. Run the Production Tool
Warning: This process will permanently delete all data on the drive.
Extract the AlcorMP .zip file and run AlcorMP.exe as an Administrator.
If the tool doesn't see your drive, try running LoadDriver.exe first to install the necessary low-level drivers.
Click Start (or "Start (S)") to begin the low-level format and firmware flash. ⚠️ Important Troubleshooting Tips
The identifier Alcor Micro Unknown [FA00] - F/W 3613 (or similar firmware versions like F006 or C2DE) typically appears when a flash drive's controller is corrupted, malfunctioning, or is a "fake" device. The Story of the "Unknown" Drive
When a computer reads a USB drive, it asks the controller (the "brain" of the USB) for its identity. In the case of Alcor Micro chips, [FA00] is a generic status code rather than a specific model number.
The Identity Crisis: The "[FA00]" designation often means the software (like ChipGenius) cannot communicate properly with the chip's internal firmware. It is effectively the controller saying, "I know I'm an Alcor chip, but I don't know who I am exactly".
The Firmware Mismatch: Firmware versions like 3613 or F006 are specific instruction sets loaded onto these controllers. If the firmware becomes corrupted, the drive may show up as "No Media," have 0MB capacity, or become write-protected.
The "Clone" Factor: Many devices reporting this specific error are found in "no-name" or fake high-capacity drives (e.g., a "2TB" drive that is actually 16GB). These often use Alcor AU6989 series controllers or Chinese clones that mimic them. Common Technical Profile Controller Vendor: Alcor Micro. Status Code: Unknown [FA00].
Typical Hardware: Often related to the AU6989SN-GT/TA family of chips.
The "No FID" Problem: Sometimes the Flash ID (FID) also shows as "Unknown" or all zeros/nines, which suggests the controller can't even "see" the memory chips it's supposed to manage. How People "Fix" the Story
For many users, this is the beginning of a repair journey using specialized "Mass Production" (MP) tools:
Identification: Users use tools like ChipGenius to find the VID (often 058F) and PID (often 1234).
The Repair: They seek out the AlcorMP utility. This software "re-flashes" the firmware, essentially giving the controller a new brain and resetting the memory capacity to its true physical limit.
Low-Level Format: If successful, the tool turns the "Unknown [FA00]" back into a recognized "AU6989" (or similar) device.
Alcor Micro USB drive showing the "Unknown FA00" error with Firmware 3613
, you typically need to re-flash the controller using a specialized mass production (MP) tool. This error usually indicates that the drive's firmware has become corrupted or the controller is unable to read the NAND flash memory. 🛠️ How to Fix Alcor Micro "Unknown FA00" 1. Identify Your Specific Chip
Before downloading tools, you must verify the exact controller and memory chip. Standard Windows properties won't show this. ChipGenius Flash Drive Information Extractor Controller model (e.g., AU6989SN) and the (a string of hex codes). 2. Find the Correct MP Tool "FA00" often requires a specific version of the Alcormp Online Recovery Search for: "AlcorMP AU6989" (or your specific chip) + "Firmware 3613". Trusted Source: FlashBoot.ru
are the most comprehensive archives for these specialized tools. 3. Flashing Procedure Disable Antivirus:
These tools are often flagged as "false positives" because they access hardware at a low level. Run as Admin: Right-click the AlcorMP.exe ) and run as administrator. Insert Drive: If the tool doesn't see it, click Refresh (G) Setup/Configuration: Password is usually blank or "000000".
In "Flash Type," ensure it matches what ChipGenius told you.
. The process can take 5–30 minutes depending on the drive size and "Scan Level." ⚠️ Important Warnings Data Loss: This process is a "factory reset." It will erase all files on the USB drive. Hardware Fail:
If the tool returns an error like "Too many bad blocks" or "Hardware Error," the physical NAND chip may be permanently damaged. Test Mode:
If the computer doesn't detect the drive at all, you may need to "short" the pins on the controller chip (Hardware Test Mode) to force the PC to recognize it as a generic device. If you'd like to proceed with the repair, tell me: Controller Model did ChipGenius show? What is the (the long code)? Are you getting a specific error code (like 30100 or 50400) when you try to run a tool?
Here’s a cleanly assembled version of the text you provided:
Alcor Micro Unknown FA00 - F W 3613
If this is intended as a device or firmware identifier, it could be read as:
The "Unknown [FA00] - F/W 3613" error typically appears when using diagnostic tools like ChipGenius or Flash Drive Information Extractor on a corrupted USB flash drive. This status indicates that the operating system recognizes the Alcor Micro controller but the firmware (F/W) is corrupted, preventing the drive from being accessed or formatted normally.
To fix this, you must use a specialized Mass Production (MP) Tool to re-flash the controller's firmware. Steps to Restore Your Drive
Warning: This process will permanently erase all data on the flash drive.
Identify the Controller: Confirm your drive's VID/PID. Most Alcor Micro drives with the FA00 controller use VID 058F and PID 6387.
Download the MP Tool: You need a version of AlcorMP that explicitly supports the FA00 (often synonymous with the AU6989SN-TA chip).
Versions such as AlcorMP v16.09.30.00 or newer are typically required. Since specific technical documentation for "Alcor Micro FA00
Reliable repositories include sites like FlashBoot.ru and USBDev.ru. Preparation:
It is highly recommended to use a 32-bit Windows XP or Windows 7 environment, as these tools often fail on 64-bit Windows 10/11 due to driver signature requirements.
Run as Administrator: Always right-click the AlcorMP.exe and select "Run as administrator". Flashing Process: Open the tool first, then plug in the USB drive.
If the drive is detected, click Setup (S). If prompted for a password, leave it blank.
Set the "Scan Level" to Full Scan4 and "Optimization" to Capacity Optimize for the best chance of recovery.
Click Start and wait. This can take anywhere from a few minutes to an hour. Why this happens ("The Long Story")
These "unknown" errors usually occur because the Flash Translation Layer (FTL)—the internal map the controller uses to find data on the memory chips—has crashed. This is often caused by: Unplugging the drive while it was writing data. Physical wear on the NAND flash chips (bad sectors).
The drive being a "fake capacity" drive where the controller is programmed to report more space than actually exists.
If the AlcorMP tool gives an error like "Too many bad blocks," the memory chip is likely physically failing, and the drive cannot be repaired.
Do you have the VID and PID numbers for your specific device from a tool like ChipGenius? AlcorMP Tool for Generic 32GB Flash Disk VID 058F PID 6387
ALCOR MICRO UNKNOWN FA00 - F/W 3613 is a cry for help from a dying or misconfigured USB flash drive controller. While you can often revive the drive as a usable storage device using Alcor’s MPTool, do not trust it with important data afterward. The root cause—poor NAND quality or counterfeit design—remains.
If the drive contained critical files, stop all DIY attempts immediately and send it to a professional lab like DriveSavers or Ace Laboratory (for PC3000 Flash). Otherwise, consider the drive e-waste and replace it with a reputable brand (SanDisk, Samsung, SK Hynix).
Need a specific MPTool version or further debugging? Provide the exact NAND chip marking (e.g., “H27UCG8T2BTR”) and I can narrow down the configuration.
The string "alcor micro unknown fa00 - f/w 3613" a specific technical identifier typically generated by low-level hardware diagnostic tools (like ChipGenius Flash Drive Information Extractor
) when analyzing a corrupted or uninitialized USB flash drive . It signifies that the device is using an Alcor Micro
controller, but the specific chip model is unrecognized ("Unknown FA00"), and it is running firmware version Understanding the Identifier Alcor Micro
: The manufacturer of the USB mass storage controller, a common component in budget-friendly or "no-name" flash drives. Unknown FA00
: This status code often indicates a communication failure between the diagnostic software and the controller. It can mean the controller is in "mask-ROM" or "safe" mode because it cannot read the NAND flash memory due to physical damage or severe firmware corruption.
: This refers to the current firmware revision (Firmware) programmed into the controller. Technical Context: The Repair Process
When a drive reports this specific error, it is usually "bricked"—it may show up in Device Manager but cannot be formatted by Windows. Recovery involves using specialized "Mass Production" (MP) tools specifically designed for Alcor chips, such as Identification
: Users must first identify the exact controller model (e.g., AU6989, AU6998) to select the correct repair tool. If the software says "Unknown," physical inspection of the chip inside the casing is often the only certain way to find the part number. The AlcorMP Utility
: This tool can re-flash the firmware (3613 or newer) and map out bad sectors on the NAND flash. Risk of Data Loss
: These "re-production" tools are destructive. They aim to restore the hardware's functionality by wiping all data and performing a low-level format to bypass damaged memory cells. Why This Happens This error often occurs due to: Sudden Power Loss
: Removing the drive while it is writing can corrupt the firmware lookup tables. NAND Degradation
: The physical memory chips inside have a limited lifespan. Once they fail, the Alcor controller cannot load its operating instructions, leading to the "Unknown" status. Counterfeit Hardware
: Drives that misreport their capacity (e.g., a 2GB chip disguised as 64GB) often crash into this state when the real storage limit is exceeded. To attempt a fix, you can look for the Online Recovery tools hosted on specialist repositories like
, though you should only proceed if you do not need to recover the data currently on the drive. Alcor Micro - USBDev.ru
The "Alcor Micro Unknown FA00 - F/W 3613" designation refers to a USB Flash Drive controller that is often misidentified or corrupted. This specific string typically appears when diagnostic tools like ChipGenius or Flash Drive Information Extractor cannot find a matching entry in their database for the hardware. Key Identification Features
Controller Model: Often maps to the Alcor AU6989SN-TA or AU6989SNCS-TA chipset.
Error Indicators: The "FA00" code is frequently associated with "No FID" (Flash ID) errors, meaning the controller cannot communicate with the memory chip.
Capacity Issues: Drives with this firmware identification often show 0 bytes, No Media, or "Write Protected" in Windows.
Common Use: Frequently found in unbranded or "fake" high-capacity USB drives that report much more storage than they actually have. Recommended Repair Tools
To fix or reflash this device, specialized "Mass Production Tools" (MPTools) are required: fake HP usb flash drives - HP Support Community - 5995925
Alcor Micro Unknown FA00 - F/W 3613: A Comprehensive Analysis
Introduction
The Alcor Micro Unknown FA00 - F/W 3613 is a mysterious device that has garnered significant attention in recent times. As a comprehensive analysis of this device, this write-up aims to provide an in-depth examination of its features, functionality, and potential applications. Our goal is to shed light on the capabilities and characteristics of this enigmatic device.
Overview
The Alcor Micro Unknown FA00 - F/W 3613 appears to be a type of microcontroller or system-on-chip (SoC) developed by Alcor Micro, a company known for producing innovative semiconductor solutions. The device is identified by its firmware version, F/W 3613, which suggests that it may be a specific iteration of a larger product line. Key insight: FA00 is not a normal operational PID
Key Features
Based on available data, the Alcor Micro Unknown FA00 - F/W 3613 boasts several notable features:
Technical Specifications
While specific technical details about the Alcor Micro Unknown FA00 - F/W 3613 are scarce, we can infer some information based on similar devices:
Potential Applications
The Alcor Micro Unknown FA00 - F/W 3613 could be used in a variety of applications, including:
Conclusion
The Alcor Micro Unknown FA00 - F/W 3613 is a fascinating device that holds much promise for a wide range of applications. While specific details about the device are scarce, its features and functionality suggest that it could be a versatile and powerful solution for embedded systems, IoT devices, and industrial automation. Further analysis and testing will be necessary to fully understand the capabilities and potential uses of this enigmatic device.
Recommendations for Future Research
To gain a deeper understanding of the Alcor Micro Unknown FA00 - F/W 3613, we recommend:
The identifiers Alcor Micro Unknown FA00 typically appear when a USB flash drive's controller is corrupted, malfunctioning, or is a counterfeit device
. In most cases, "FA00" is not a legitimate model number but a generic error code or placeholder indicating that the management software cannot correctly identify the physical controller chip. Identifying the Root Cause When diagnostic tools like ChipGenius Flash Drive Information Extractor return these specific strings, it usually means: Firmware Corruption
: The controller's internal software (Firmware 3613) is damaged, preventing the operating system from seeing the actual storage capacity (often showing "0 MB" or "No Media"). Pseudo-Controller : The "FA00" ID is frequently associated with AU6989SN-GT/TA
or similar series controllers where the Flash ID (FID) cannot be read (e.g., returning 89 89 89 89 89 89 Hardware Failure
: A physical break in the connection between the controller and the flash memory chip. Potential Solutions
If you are trying to recover the drive, you will likely need specialized "Mass Production" (MP) tools from Alcor Micro Identify the True Controller ChipGenius
to find the actual hardware ID (e.g., AU6989, AU6998). If it still says "FA00," you may need to open the drive's casing to read the laser-etched model number directly off the chip. Use AlcorMP Tools
: Once the true model is known, download the corresponding version of : These tools are designed for factory formatting and will erase all data on the drive.
If the standard tools fail to see the drive, you might need a "Rework" version of the utility, such as Alcor Change PID/VID Rework , to reset the device's identification strings. Check Drivers : Sometimes a persistent driver like mpszfilt.sys
(installed by some Alcor utilities) can cause conflicts with other USB devices if the utility crashes. Relaunching and properly closing the tool usually resolves this.
Are you trying to recover data from this drive, or are you simply looking to make it functional again?
AlcorMP (Последняя версия ALCOR U2 MP v23.08.07.00.H)
The identification of a hardware component as Alcor Micro Unknown [FA00] - F/W 3613
typically signifies a critical error state in a USB flash drive or memory card controller. In this state, the hardware is physically connected, but the operating system cannot communicate with the underlying flash memory chip, often due to corrupted firmware or physical degradation. Understanding the "Unknown [FA00]" Identifier
The Alcor Micro [FA00] code is not a specific model number but rather a generic status reported by diagnostic tools like ChipGenius or Flash Drive Information Extractor when the controller (the "brain" of the USB drive) fails to initialize correctly.
Firmware Mismatch: The F/W 3613 designation refers to a specific version of the internal firmware. If the controller reports "Unknown [FA00]" alongside this version, it often indicates the controller is alive but the Flash ID (FID)—the unique code identifying the memory chip—is missing or unreadable.
Hardware Mapping: Documentation suggests that "Alcor [FA00]" is frequently associated with the Alcor AU6989SN-TA or AU6989SNCS-TA controller families. These are widely used in low-cost or "generic" flash drives. Root Causes of Failure
When a device presents this error, it is usually "dead" to the operating system, showing 0 Bytes capacity or "No Media". This occurs due to:
Firmware Corruption: The low-level instructions (F/W 3613) have become desynchronized from the hardware, preventing the controller from mounting the memory partition.
Bad Blocks: NAND flash memory wears out over time. If critical system areas of the chip fail, the controller enters a "safe mode" or "error mode" (FA00) to prevent further damage.
Physical Faults: A broken trace or cold solder joint between the controller and the flash chip can lead to a failure to read the FID, triggering the "Unknown" status. Potential Recovery Steps
Fixing this error requires "Mass Production Tools" (MPTools), which are specialized utilities designed to re-flash the controller and re-map the memory.
Identify the Controller: Use tools like ChipGenius to confirm if the actual hardware is an AU6989 series chip.
Find the MPTool: Locate the version of AlcorMP or FC_MpTool that specifically supports the 3613 firmware or the identified AU6989 chip.
Low-Level Format: Running these tools will perform a low-level format. Note that this process destroys all data on the drive but can often restore the device's functionality for future use.
For drivers related to working Alcor Micro hardware (like integrated card readers), official sources such as the Lenovo Support or manufacturer-specific portals should be used.
Alcor AU6989SN-TA Firmware Issues | PDF | Usb Flash Drive - Scribd
Please see the following from UsbDriveInfo: Код:[Выделить] [Развернуть] НОВИЧОК Volume: D: Controller: Alcor 0xFA00. Сообщения: 6.
Yes, but with caveats.
If the device shows FA00, the controller is still responding. This means you have a 50–70% chance of reviving it using Alcor’s proprietary mass production tools (MPTools). However:
Alcor Micro is a Taiwanese company known for USB controller chips used in flash drives, card readers, and other USB mass-storage devices. If you see a device identified as “Alcor Micro Unknown FA00 - FW 3613” (or similar) on your computer, it usually indicates the operating system recognizes the hardware vendor but cannot identify the device model or its driver/firmware details. This article explains what that message means, common causes, and practical steps to resolve the issue.