Actia Psa Xs Evolution 9780z5 Driver ❲720p • 2K❳

The ACTIA PSA XS Evolution (Reference 9780Z5) is one of the most iconic diagnostic interfaces used by Citroën and Peugeot vehicles. Because it uses a legacy hardware architecture (often utilizing the PCAN-USB adapter style internally), it requires specific drivers to communicate with modern Windows PCs.

Below is a complete guide drafted for use in a technical manual, readme file, or support knowledge base.

Q2: Can I use the driver with a clone interface?

A: Many Chinese clones mimic the 9780Z5 hardware ID. The driver will install, but you may experience random bricking due to fake FTDI chips. Use original ACTIA for reliability. actia psa xs evolution 9780z5 driver

Part 1: Understanding the Actia PSA XS Evolution (Hardware 9780Z5)

Before diving into driver files, let's understand the hardware you are holding.

The Actia PSA XS Evolution is a multi-protocol pass-through interface. It allows a laptop running DiagBox, PP2000, or Lexia-3 software to communicate with the CAN, VAN, and K-Line networks in PSA vehicles. Over the years, Actia released several hardware revisions. The 9780Z5 is a specific PCB (Printed Circuit Board) revision that differs slightly in its USB controller chipset from older models like the 9780Z4. The ACTIA PSA XS Evolution (Reference 9780Z5) is

Mastering the ACTIA PSA XS Evolution 9780Z5 Driver: Installation, Troubleshooting, and Optimization

In the world of professional automotive diagnostics—specifically for the PSA Group (Peugeot, Citroën, DS, and lately, Opel/Vauxhall models)—the ACTIA PSA XS Evolution stands as a gold standard. However, even the most powerful hardware is rendered useless without the correct software bridge: the driver. Specifically, the component referenced by the identifier 9780Z5 is a critical piece of this ecosystem.

If you are a garage owner, a mobile diagnostician, or a passionate PSA enthusiast, understanding how to properly install, troubleshoot, and maintain the ACTIA PSA XS Evolution 9780Z5 driver is non-negotiable. This article provides a deep dive into everything you need to know. Q2: Can I use the driver with a clone interface

Common Issues and Resolutions for the 9780Z5 Driver

Even advanced users face hurdles. Here is a troubleshooting matrix specific to actia psa xs evolution 9780z5 driver problems.

| Error Message | Likely Cause | Solution | |---------------|--------------|----------| | "Device descriptor request failed" | Corrupted EEPROM on the ACTIA board | Use MProg or FT_PROG to reload default USB descriptors. | | "This device cannot start. (Code 10)" | Conflicting serial driver (e.g., Arduino, Prolific) | Uninstall all COM port drivers. Use USBDeview to remove ghost devices. | | DiagBox says "No interface found" | Driver installed but software points to wrong COM port | In DiagBox configuration, manually set the COM port to match Device Manager. | | Random disconnections during SIDI/EDC17C10 programming | USB power saving enabled | Go to Power Options → USB selective suspend → Disabled. Also, in Device Manager → USB Root Hub → Properties → Power Management → Uncheck "Allow computer to turn off". | | Driver installs but shows "ACTIA PSA XS (Old)" | Wrong INF file used | Force update driver → "Let me pick from a list" → Choose the specific "9780Z5" entry, not generic ACTIA. |

Phase 3: Installation Process

  1. Run the installer as Administrator (Right-click → Run as Administrator).
  2. If using manual INF installation:
    • Plug the 9780Z5 into a USB 2.0 port (avoid USB 3.0 hubs).
    • When Windows asks for a driver, choose "Browse my computer for drivers".
    • Point to the folder containing actia_xs_evolution.inf.
    • Select "ACTIA PSA XS Evolution (9780Z5)" from the list.
  3. Complete the installation: You will see a popup confirming "Device ready to use."
  4. Verify in Device Manager:
    • Expand "Ports (COM & LPT)".
    • Look for "ACTIA PSA XS Evolution (COMx)" – note the COM port number.
    • Expand "Universal Serial Bus devices" → "ACTIA PSA XS Evolution USB Module".